EasyManua.ls Logo

B-K lighting LT User Manual

B-K lighting LT
3 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade
Optional
Stability Flange
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
TOOLS
NEEDED:
By Others
5/64” Allen Wrench
Phillips Screwdriver
Waterproof Wire Connectors
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • info@bklighting.com
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade
Optional
Stability Flange
This set of instructions works for:
LT - Litestick™
LT-L - Litestick™ Style L
LT-T - Litestick™ Style T
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade
Optional
Stability Flange
LT-L
TOOLS
NEEDED:
By Others
18 Gauge Wire
Optional Stability
Flange
Power Pipe
Adjustable
Stem
Fixed
Stem
DATE
11-30-16
REFERENCE NUMBER
INS001109
Warning Flammable Hot Surface
LT
Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
Follow product label information and instructions.
Qualified Personnel must perform all servicing or relamping of
this product.
Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
Replace lamp only with correct wattage and type of lamp
marked on fixture label.
All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when turning on.
Do not touch hot lens, guard, or enclosure
(see diagram/picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth.
Oil from skin may damage lamp.
Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
· SUITABLE FOR WET LOCATIONS · SUITABLE FOR IN-GROUND RECESSED INSTALLATION
IMPORTANT LISTINGS AND CERTIFICATIONS
Fixed Stem
with
T - housing
option
LT-T
& Low Voltage Halogen LT™/ LT-L™/ LT-T™
Installation Instructions
High Voltage
Question and Answer IconNeed help?

Do you have a question about the B-K lighting LT and is the answer not in the manual?

B-K lighting LT Specifications

General IconGeneral
CategoryLighting Equipment
ManufacturerB-K Lighting
LampLED
MaterialAluminum
Voltage120-277V

Summary

General Safety and Model Information

Critical Safety Instructions

Mandatory safety guidelines to prevent fire, injury, and ensure correct operation.

Installation Compliance and Care

Essential safety information for installation compliance and product care.

Product Model Identification

Overview of LT, LT-L, and LT-T Litestick™ models covered by these instructions.

Product Certifications

Information on product certifications and environmental suitability for wet/in-ground use.

Power Pipe™ Installation

Site Preparation and Excavation

Excavating trenches and holes for Power Pipe™ installation.

Pipe and Wiring Setup

Installing the Power Pipe™ and pulling low voltage wiring.

Backfilling and Final Grade

Backfilling with gravel or sand and setting the final grade.

Stem Fixture Installation

Wiring to Transformer

Connecting fixture leads to the remote transformer using waterproof connectors.

Fixture Mounting

Securing the fixture to the Power Pipe™ using specified screws.

Adjustable Stem Height

Adjusting and locking the stem height for desired fixture placement.

Fixture Options and Lamp Installation

Transformer Housing Warning

Critical warning: Transformer housing must be above grade; below grade voids warranty.

Fixed Stem/T-Housing Installation

Steps for installing fixtures with fixed stems and T-housing options.

Integral Transformer Wiring

Connecting branch circuit wires to the integral transformer via wiring diagram.

Lamp Replacement

Instructions for installing Halogen or BKSSL lamps, including driver components.

Lamp Installation Cautions

Warnings on touching lamp glass, set screw tightening, and O-ring seal integrity.