Baby Lock Quilter's Choice BLQC2 User Manual (English)

Other manuals for Baby Lock Quilter's Choice BLQC2

Questions and Answers:

R
Richard MillerAug 17, 2025
Why are stitches skipped on my Baby Lock Sewing Machine?
- E
  Erin BrownAug 17, 2025
  Skipped stitches on your Baby Lock Sewing Machine can occur if the upper thread isn't threaded correctly, so ensure it is properly threaded. Also, verify that you're using the correct combination of fabric, thread, and needle. Replace the needle if it's bent or blunt, and make sure it's correctly installed. Additionally, dust accumulation under the needle plate or in the bobbin case can cause skipped stitches, so remove the needle plate cover and clean the race.
V
Vincent LopezAug 19, 2025
What to do if my Baby Lock Quilter's Choice BLQC2 does not operate?
- B
  Bobby GuzmanAug 19, 2025
  If your Baby Lock Sewing Machine doesn't operate, check the following: Make sure the machine is turned on. If it is on, ensure you've pressed the 'Start/Stop' button. Also, verify that the presser foot lever is lowered. If you're using a foot controller, do not use the 'Start/Stop' button; disconnect the foot controller to use the 'Start/Stop' button.
J
johnrobertsAug 22, 2025
Why does the needle break on my Baby Lock Quilter's Choice BLQC2?
- C
  Christopher AlexanderAug 22, 2025
  Needle breakage on your Baby Lock Sewing Machine can occur for several reasons. Ensure the needle is correctly installed and the needle clamp screw is firmly tightened with a screwdriver. Replace the needle if it's bent or blunt. Also, verify that you're using the correct combination of fabric, thread, and needle, and that the presser foot is appropriate for the stitch you're using. If the upper thread tension is too tight, loosen it. Also, make sure the spool is correctly installed, and you are using a bobbin designed specifically for this machine. If the area around the hole in the needle plate or presser foot, or the bobbin case is scratched or has a burr, consider replacing these parts.
J
jasonarroyoAug 28, 2025
What to do if lower thread is tangled or breaks in Baby Lock Sewing Machine?
- U
  uhudsonAug 28, 2025
  If the lower thread is tangling or breaking in your Baby Lock Sewing Machine, make sure the bobbin thread is correctly installed. Replace the bobbin if it's scratched, doesn't rotate smoothly, or has a burr. Remove any tangled thread and clean the race. Ensure you are using a bobbin designed specifically for your machine, as incorrect bobbins will not work properly.
M
Mr. Michael Ruiz DDSAug 30, 2025
Why is the fabric wrinkled when sewing with my Baby Lock Quilter's Choice BLQC2?
- V
  vbridgesAug 30, 2025
  Fabric wrinkling while sewing with your Baby Lock Sewing Machine can occur if the upper thread isn't threaded correctly or the bobbin is incorrectly installed; ensure both are properly set up. Also, make sure the spool is correctly installed. The issue could also stem from using an incorrect combination of fabric, thread, and needle, so select appropriate ones. Replace the needle if it's bent or blunt. If you're sewing thin fabrics, try shortening the stitch length or using a stabilizer material under the fabric. Lastly, incorrect thread tension can cause wrinkling, so adjust the upper thread tension.
S
Stephanie HermanSep 2, 2025
How to fix incorrect thread tension on Baby Lock Quilter's Choice BLQC2?
- R
  rodriguezscottSep 2, 2025
  To fix incorrect thread tension on your Baby Lock Sewing Machine, first ensure the upper thread and bobbin thread are correctly threaded and installed, respectively. Verify that you're using the correct combination of fabric, thread, and needle. Also, make sure the presser foot holder is correctly installed. Adjust the tension of the upper thread as needed. Finally, ensure you're using a bobbin designed specifically for your machine.
N
Nicholas ColemanSep 5, 2025
What causes a high-pitched noise while sewing on Baby Lock Sewing Machine?
- A
  Angela SmithSep 5, 2025
  A high-pitched noise while sewing on your Baby Lock Sewing Machine may be due to dust accumulation in the feed dogs or bobbin case, so try cleaning the race. Ensure the upper thread is correctly threaded. Also, using incorrect bobbins may cause this issue; use only bobbins designed specifically for this machine.
P
Preston DiazSep 8, 2025
Why can't I use the needle threader on my Baby Lock Sewing Machine?
- K
  Kevin CarrilloSep 8, 2025
  If you cannot use the needle threader on your Baby Lock Sewing Machine, make sure the needle has been raised to the correct position by pressing the 'Needle Position' button. Also, ensure the needle is correctly installed.
J
johnwattsSep 12, 2025
Why is the stitch not sewn correctly on my Baby Lock Sewing Machine?
- K
  kathleen42Sep 12, 2025
  If the stitch isn't sewing correctly on your Baby Lock Sewing Machine, ensure you're using the appropriate presser foot for the type of stitch you want to sew. Adjust the tension of the upper thread. Also, check for tangled thread, especially in the bobbin case, and clean the race if necessary.
D
Diana WoodSep 13, 2025
What to do if the fabric does not feed through my Baby Lock Quilter's Choice BLQC2?
- J
  joshua70Sep 13, 2025
  If the fabric isn't feeding through your Baby Lock Sewing Machine, check that the feed dogs are raised by sliding the drop feed lever to the right (as seen from the rear of the machine). If the stitch is too short, lengthen it. Ensure you're using the appropriate presser foot for the type of stitch you wish to sew. If the pressure of the presser foot is weak, turn the presser foot pressure dial to the left to increase the pressure. Also, check for tangled thread, especially in the bobbin case, and clean the race if necessary.