Bakbar E92 - User Manual

To Next Page

SWIFTGRILL

Model: E92

Cooking Area: 696 x 450mm 27½" x 17¾"

INSTALLATION

IMPORTANT - FIXED WIRE INSTALLATIONS MUST INCORPORATE AN ALL-

POLE DISCONNECTION SWITCH.

All appliances are to be installed by a Qualified Person, who must check unit is operating correctly.

THIS APPLIANCE MUST BE EARTHED (GROUNDED). All installations are to be in accordance

with local health, safety and electrical requirements.

E92 for 220-240 Volts AC - 7200W 30.0 Amp at 240 Volts

A 3-wire 30 Amp cable should be fitted to this appliance for connection to a single phase 30 Amp

supply (Phase + Neutral + Earth).

Note: This appliance may also be connected to a 2 phase supply if required. Connection of the 2

phase supply should be in accordance with the circuit schematic alternative on this

instruction sheet.

OPERATION

This unit is designed for cooking food directly on the hotplate surface. The elements under the plate

are thermostatically controlled. The pilot light indicates when the element is heating.

FOOD TEMP

ºC ºF

Meat - Bacon 180 355

- Frankfurters 180 355

- Ham Slices 180 355

- Hamburger Patties 160 320

- Lamb Chops 190 375

- Steak 200 400

- Sausages 150 300

Eggs 140 285

Fish 190 375

French Toast 190 375

Griddle Cakes 190 375

Onions 180 355

Mushrooms 180 355

Turn the thermostat dial clockwise to the desired temperature. When the pilot light goes out, the

desired cooking temperature has been reached. Turning the dial to higher settings will not reduce

the heat up time. Model E92 has two controls, one for the left half and one for the right half.

Need help?

Do you have a question about the Bakbar E92 and is the answer not in the manual?

The document describes the Bakbar Swiftgrill Model E92, a commercial electric griddle designed for cooking food directly on its hotplate surface.

Function Description

The Swiftgrill E92 is an electric griddle that uses thermostatically controlled elements located under the cooking plate to heat the surface. A pilot light indicates when the elements are actively heating. This unit is designed for direct cooking of various food items. The E92 model features two separate controls, one for the left half of the cooking surface and one for the right half, allowing for independent temperature management across the griddle.

Important Technical Specifications

Model: E92
Cooking Area: 696 x 450mm (approximately 27½" x 17¾")
Electrical Requirements (for E92):
- 220-240 Volts AC
- 7200W
- 30.0 Amp at 240 Volts
Wiring: Requires a 3-wire 30 Amp cable for connection to a single-phase 30 Amp supply (Phase + Neutral + Earth). It can also be connected to a 2-phase supply, with specific wiring instructions provided in the circuit schematic.
Installation: Fixed wire installations must incorporate an all-pole disconnection switch. Installation must be performed by a Qualified Person and comply with local health, safety, and electrical requirements. The appliance must be earthed (grounded).

Usage Features

The Swiftgrill E92 offers precise temperature control for various food items, with recommended cooking temperatures provided in both Celsius and Fahrenheit:

Food	Temp (°C)	Temp (°F)
Meat - Bacon	180	355
Meat - Frankfurters	180	355
Meat - Ham Slices	180	355
Meat - Hamburger Patties	160	320
Meat - Lamb Chops	190	375
Meat - Steak	200	400
Meat - Sausages	150	300
Eggs	140	285
Fish	190	375
French Toast	190	375
Griddle Cakes	190	375
Onions	180	355
Mushrooms	180	355

To operate, the user turns the thermostat dial clockwise to the desired temperature. The pilot light will illuminate during heating and extinguish once the set temperature is reached. Turning the dial to higher settings will not decrease the heat-up time. The dual controls allow for different temperatures on each half of the griddle.

Maintenance Features

Cleaning:

After use, the hotplate should be scrubbed with a brush, detergent, and water.
The grease drawer should be emptied regularly.
Accumulated carbon can be removed using a scraper and a fine grit griddle brick.
Occasionally, the plate can be bleached with vinegar when cold.
Important Note: Do not use a griddle brick on chrome-plated griddles.
Crucial Warning: This appliance must NOT be cleaned with a water jet.

Servicing (DISCONNECT POWER SUPPLY BEFORE SERVICING): Servicing should only be performed after disconnecting the power supply.

Access: Remove the grease drawer, turn the unit upside down, and remove the panel marked "service access" by unscrewing the four nuts holding the base panel.
Thermostat Replacement:
1. Remove thermostat wiring, knob, and mounting nut.
2. Lift the control assembly over the front of the unit.
3. Withdraw the thermostat through the cutout in the base panel.
4. Remove element clamps and insulation.
5. Replace the thermostat and position its bulb under the insulation strip.
6. Refit insulation, clamps, base panel, and cover panel.
Element Replacement:
1. Remove element wiring.
2. Lift the control panel assembly over the front of the unit.
3. Remove element clamps.
4. Replace the element, wiring, insulation, clamps, base panel, and cover panel.

Spares: A list of common spare parts is provided. For parts not listed, the model and serial number, along with a description of the required part, should be included when ordering.

Description	Model E92 Part Number
Element 220-240V	10280
Thermostat	11987
Knob °C	15563
Knob °F	14097
Pilot Light	13528

The document also includes a circuit diagram for both single-phase and two-phase connections, with a specific note for two-phase wiring: "For 2 Phase, connect RH Thermostat to terminal marked L2."

Bakbar E92 Specifications

General

Brand	Bakbar
Model	E92
Category	Grill
Language	English