BALZER ELIMINATOR VACUUM TANK Series

Questions and Answers

D
david76Aug 1, 2025
How to troubleshoot steering problems in BALZER ELIMINATOR VACUUM TANK?
- J
  jenniferjonesAug 1, 2025
  To troubleshoot steering issues with your BALZER Farm Equipment, ensure the steering hydraulic lever is in the “FLOAT” position. Also, verify the hydraulic connections to the tractor: the YELLOW coded hoses should connect to the right side of the tractor’s hydraulic bank, with the hose having one stripe connected to the RETURN port and the hose with two stripes to the PRESSURE port. Finally, grease the kingpins (if equipped) and the tie rod daily, both when the wheels are straight and fully extended.
Y
ygarrettAug 5, 2025
What to do if hydraulic controls are not working properly on BALZER Farm Equipment?
- A
  Anna ValenciaAug 5, 2025
  To resolve hydraulic control issues with your BALZER Farm Equipment, begin by checking the hydraulic connections to the tractor and ensuring that the tractor’s hydraulic fluid levels are adequate. Inspect the hydraulic system for any leaks or hose line damage. You may also want to attach the tractor to a different implement to determine if the problem lies with the tractor or the implement. If the problem is with the tractor, contact your local farm equipment service center.
B
Barbara WilliamsAug 9, 2025
Why is the PTO not working on my BALZER ELIMINATOR VACUUM TANK Farm Equipment?
- N
  Nathaniel ParkerAug 9, 2025
  If the PTO on your BALZER Farm Equipment isn't working, first check that the PTO drive lever on the tractor is engaged and that the PTO is properly connected to the tractor. Disengage the PTO, shut off the tractor, and remove the key. Inspect the PTO shaft’s shear bolt; replace it if broken, damaged, or missing. Disconnect the PTO from the tractor and engage the PTO drive on the tractor to check if the tractor’s PTO shaft is turning.
S
Sean MartinezAug 14, 2025
How to fix Raven SCS660 NVM not controlling flow properly in BALZER ELIMINATOR VACUUM TANK Farm Equipment?
- D
  danielsbrittanyAug 14, 2025
  If the Raven SCS660 NVM on your BALZER Rite Rate Flow System isn't controlling flow properly, begin by checking the Raven SCS660 NVM programming. If the programming is not correct, see “Rite Rate Flow System Programming”. If the programming is correct, check all connections between the Raven SCS660 NVM Controller and the Krohne Optiflux 4100C. Check if the Sky Trak GPS has an unobstructed view of the sky and check GPS on another GPS capable device to see if that device is able to obtain a GPS signal. Check that the gate valves are open when the system is operating and the pump is operating properly.
M
martha43Aug 18, 2025
What to do if the slurry pump is not working on BALZER ELIMINATOR VACUUM TANK Farm Equipment?
- E
  Elizabeth BarberAug 18, 2025
  If the slurry pump on your BALZER Farm Equipment is not working, check if the tank is empty. Ensure that the hydraulic lever controlling the hydraulic motor is engaged and that hydraulic hoses are properly connected to the tractor, checking for any leaks. Also, verify the tractor’s hydraulic fluid levels and check if the gate valves are open or closed.
P
paulavargasAug 22, 2025
Why is the vacuum pump not working (continued) on my BALZER ELIMINATOR VACUUM TANK?
- J
  joanna17Aug 22, 2025
  To address a vacuum pump that is not working on your BALZER Farm Equipment, check the hydraulic motor and ensure that the hydraulic lever controlling it is engaged. Verify that the hydraulic hoses are properly connected to the tractor and inspect them for leaks. Also, check the tractor’s hydraulic fluid levels and inspect the vacuum and pressure hoses coming off the vacuum pump, as well as the flexible suction tube on the boom, for any leaks. Finally, check the vacuum pump’s internal vanes for excessive wear.
H
hfriedmanAug 27, 2025
What causes backing up and steering not locked straight on BALZER ELIMINATOR VACUUM TANK Farm Equipment?
- J
  Jordan RowlandAug 27, 2025
  If your BALZER Farm Equipment is backing up and the steering is not locked straight, make sure the steering hydraulic lever is NOT in the “FLOAT” position and check the hydraulic connections to the tractor.