EasyManua.ls Logo

Banda Audioparts VIKING 15.000 User Manual

Banda Audioparts VIKING 15.000
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
CEP
: 13148-1
15
Output:
1 channel 15.000Wrms 1ohm - 12.6Vdc
1 channel 9.800Wrms 2ohms - 12.6Vdc
1 channel 19.000Wrms 1ohm - 14.4Vdc
Current draw at full power(average music program): 630A*
*Equivalant to current draw with resistive load and sinusoidal signal at half power.
TECHNICAL SPECIFICATION
VIKING 15.000
02 .......... Technical Specification
03 .......... Technical Specification, front Panel and active filter
Power Supply, Signal Input and Power Output Sections04 ..........
Clip Indicator04 ..........
Subsonic and Crossover Controls 04 ..........
05 ..........Connetion Example
06 ..........Connection Example
07 .......... Protection System and Troubleshooting
08 .......... Warranty
Front panel view
2 3 41
Operation topology: Class D
12db/octave variable active Linkwitz-Riley crossover: 13Hz - 2kHz
Frequency response: 13Hz - 2kHz (filter ON)
Frequency response: 13Hz - 3kHz (filter OFF)
Variable subsonic filter: 13Hz - 120Hz (filter ON)
Fuse: MIDIVAL 125A (x 6) + 60A (x 1)
Clip indicator
THD < 0.5%
SNR > 82dB
Damping factor > 10
Input sensitivity: 160mVRMS – 6VRMS
Differential input signal impedance: 17kOhms
Cooling fans
Idle Current: 5.3A
Dimensions: 29.6”L x 2.5”H x 10.1”W
Weight: 29.8lb
These values are typical and may present some minor variation.
TECHNICAL SPECIFICATION
1. Blue LED: On
2. Red LED: Blinking - Output distorted (Clip) / Constant - Output short circuit
3. Yellow LED: Fblinking - Low voltage battery / Constant - Fuse blown or missing)
4. Gain Control
www.bandaaudioparts.com
Made in Brazil
COSTUMER SERVICE:
55 (19) 3844-7173 - (19) 3844-7465 - (19) 3844-4923 •
BANDA@BANDAAUDIOPARTS.COM
WARRANTY
Banda Audioparts warrants this equipment to be free of all defects in material and workmanship for
a period of 12 months from the date of purchase
Within the period of this warranty, Banda Audioparts will repair or replace, free of charge, any part
proving defective in material or workmanship.
Warranty Exclusions:
1. Damage resulting from misuse, abuse, accident, alterations or improper installation;
2. Damage resulting from installation in surfaces subjected to high levels of vibration;
3. Corrective work necessitated by repairs made by anyone other than a Banda Audioparts
authorized service technician;
This warranty does not cover shipping costs.
The defective equipment must be shipped to the factory or to an authorized service center
Rua Manoel Joaquim Filho, 353 - Jd. Santa Terezinha II - Paulínia - SP - Brazil -
Banda Audioparts reserves the right to change the product and its specifications at any time
without prior notice.
Note:Permanent Technical Support
After the warranty expires, Banda Audioparts will continue to provide extensive technical
assistance directly or through its network of authorized service, charging, however, the repair
services and replacement of components
Warning: Continuous expose to sound pressure levels over 85dB may cause permenent hearing loss.
REGISTRATION DATA
Name:
Invoice: Date: Phone:
Address:
Shop: Phone:
08
USER MANUAL
INDEX
Linkwitz-Riley filter activeted by switch
Switch ON: Filter enable (Linkwitz-Riley 12dB/8ª)
Switch OFF: Filter desable ON OFF
OBS.: To access the filter switch remove the plastic cover under the amplifier.
The factory default filter position is ON.
Question and Answer IconNeed help?

Do you have a question about the Banda Audioparts VIKING 15.000 and is the answer not in the manual?

Banda Audioparts VIKING 15.000 Specifications

General IconGeneral
Signal to Noise Ratio> 90dB
Frequency Response10Hz - 3KHz
Minimum Impedance1 Ohm
Weight7.2Kg
Channels1
Input Sensitivity0.2V - 6V
Power @ 12.6V 4 Ohms4800W
Input Voltage9V - 16V
Input Impedance10K Ohms
Crossover Low Pass50Hz - 250Hz
Bass Boost0 - 12dB

Summary

Warranty Information

Warranty Exclusions

Details on conditions that void the equipment warranty, including misuse, damage, and unauthorized repairs.

Technical Specifications Overview

Output Power Ratings

Specifies the power output of the amplifier across different impedance loads and voltage inputs.

Front Panel Controls and Indicators

Describes the function of LEDs (Blue, Red, Yellow) and the Gain Control on the amplifier's front panel.

Detailed Technical Specifications

Power Supply and Signal Sections

Details on power supply connections, signal input, and power output configurations.

Subsonic and Crossover Frequency Controls

Explanation of the variable subsonic and crossover filter settings and their functions.

Clip Indicator Functionality

Explains the purpose and behavior of the clip indicator LED for output distortion.

Connection Examples

Protection and Troubleshooting Guide

Protection System Features

Covers short circuit, low voltage, and inverted power supply protection mechanisms.

Troubleshooting Output Noise

Provides steps to diagnose and resolve issues related to output noise in the audio system.

Important Installation Notes

Key recommendations for power cable usage, impedance matching, and electrical connections.