Need help?Do you have a question about the Bang-Olufsen BeoSound Ouverture 2637 and is the answer not in the manual?
General| Type | Stereo System |
|---|---|
| Manufacturer | Bang & Olufsen |
| Model | BeoSound Ouverture 2637 |
| Frequency Response | 20 Hz - 20 kHz |
| Tuner | FM/AM |
| Tape Recorder | Yes |
| CD Player | Yes |
| Connectivity | RCA |
| Power consumption | 25W |
| Signal-to-Noise Ratio | 90 dB |
| Outputs | Headphones |
Overview of the receiver and S-sounder module.
Details of the microcomputer module.
Information about the display module.
Details of the keyboard module.
Information on the receiver and sensor module.
Details on the tape data control module.
Information on the CD drive motor system.
Details on CD/rever motor control.
Information on light/rever motor control.
Technical electrical specifications of the device.
Specifications related to the tuner section.
Details about the device's connection ports.
Specifications regarding the power supply unit.
Physical dimensions of the device.
Important notes related to specifications.
Wiring diagram for specific transformer types and regions.
Wiring diagram for other transformer types and regions.
Guide to programming the device's functions.
Instructions for operating the radio function.
Instructions for operating the tape deck.
Tips for adjustment and repair procedures.
Explanation of system component controls and their interactions.
Guidance on how to correct wiring issues in the diagram.
Information regarding the different supply voltages used.
Clarification of box symbols in the circuit diagrams.
List of electrical parts for PCB 1.
Part list for FM/AM, RF, IF decoder components.
List of electrical parts for PCB 3.
Part list for the microcomputer.
List of electrical parts for PCB 5.
Part list for the display unit.
List of electrical parts for PCB 6.
Part list for IR receiver and door sensor components.
List of electrical parts for PCB 7.
Part list for tape-related components.
List of electrical parts for PCB 8.
Part list for CD player components.
List of electrical parts for PCB 9.
Part list for light and motor control components.
List of electrical parts for PCB 12.
Part list for power supply and pre-amplifier.
List of electrical parts for PCB 13.
Part list for the Master Link microcomputer.
List of electrical parts for PCB 14.
Part list for the Master Link audio interface.
List of electrical parts for PCB 15.
Part list for the transformer.
List of electrical parts for the Tuner PCB.
List of electrical parts for PCB 28.
Part list for headphone components.
List of electrical parts for PCB 29.
Part list for RDS components.
Exploded view of the front mechanical parts.
Exploded view of the chassis mechanical parts.
List of chassis mechanical parts.
List and details of screws and handles.
List and details of tone handles.
List of mechanical parts for chassis.
Reference to the owner's manual.
Reference to the settings guide.
List of mechanical parts for the tape deck.
Further mechanical parts for the tape deck.
List of mechanical parts not depicted in diagrams.
Instructions for entering and using test mode.
Procedures for adjusting RF components.
General tips for repair.
Procedures for adjusting AM components.
Adjustment procedure for the detector.
Steps to adjust the FM display.
Procedure for FM offset adjustment.
Adjusting channel separation.
Procedure to adjust the FM stop level.
Mechanical adjustments for the tape recorder.
Adjusting height and azimuth on the tape recorder.
Adjusting height and tape guide.
Adjustment for azimuth side 1.
Electrical adjustments for the tape recorder.
Adjustments for the right and left channels.
Procedure for noise reduction adjustment.
Adjusting the tape speed.
Adjusting parameters within test mode.
Adjusting the recording boost level.
Adjusting the HX filter.
Procedure for bias filter adjustment.
Adjusting the Cr bias.
Adjusting the Fe bias.
Adjusting the MP bias.
Adjusting recording current for Cr bias.
Procedure for adjusting focus offset.
Details on potentiometer steps for adjustment.
How to check the laser supply.
How to dismantle PCB from tape transport.
Chart detailing lubrication points and lubricants.
Steps for replacing the CD transport mechanism.
Procedure for removing the gearbox for the CD clamp.
Steps to remove the tape recorder transport mechanism.
How to manage the wire system for glass doors.
Steps for dismounting rail A.
Steps for dismounting rails D and C.
How to mount the wire for glass doors.
Procedure for readjusting the wire.
Overview of available test functions.
How to display the tuner variant.
How to display the SW version.
Performing a display test.
Signal open/close for Master Link.
How to delete all preset programs.
Service program for the CD section.
Information on IR doors and PCB6.
Details on the Master Link data receiver/transmitter.
Table of wow frequencies and error sources.
To Next Page
