EasyManua.ls Logo

Barikell MK8 120 - User Manual

Barikell MK8 120
31 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
INSTRUCTIONS for use
Model: MK8 120
FLOAT MACHINE
MK8 120
WITH MECHANICAL
CONTROLS
BARIKELL s.r.l
Via Razzaboni,118
41100 – Modena ( Italy)
Tel 059.311178 fax 059.311111

Table of Contents

Questions and Answers

  • R
    Robin MunozAug 13, 2025
    What to do if my Barikell MK8 120 engine does not start?
    • H
      Heidi AndersonAug 13, 2025
      If the engine of your Barikell Trowels doesn't start, several factors could be at play. Ensure the fuel tank has the correct fuel type. Check that the fuel cock is open. A clogged fuel filter should be replaced. Make sure the choke isn't fully open and that the air filter is clean. Inspect the spark plug, clean it, or replace if needed. For ignition difficulty or a flooded engine, check the plug connection. A flat battery needs recharging or replacing, and the emergency stop should be off.
  • J
    Jennifer JonesAug 17, 2025
    Why is my Barikell MK8 120 Trowels float machine leaking oil?
    • A
      Amanda CampbellAug 17, 2025
      If your Barikell float machine is leaking oil, it could be due to several reasons. First, check if there's too much oil in the reduction gear and unscrew the cap to release excess oil. Next, verify that the screws on the reduction gear covers are tightened properly. If the issue persists, it may be due to defective gaskets or a worn oil seal on the central and side shaft, in which case you should contact our technical service. Also, check for oil leaks from the engine itself, and if found, contact our technical service.
  • K
    kristina97Aug 21, 2025
    Why is my Barikell Trowels float machine bouncing on the floor?
    • A
      Andrea GonzalesAug 21, 2025
      If your Barikell float machine bounces on the floor, it could be due to hardened cement under the spider or blades, so cleaning them is advised. Unevenly worn blades can also cause bouncing, so adjust the blade inclination. Additionally, ensure the drive control is perfectly vertical by adjusting its position, and check if the blades are maladjusted, requiring adjustment. If the central shaft is bent, you should contact our technical service.
  • L
    Lacey MitchellAug 25, 2025
    Why is there a drop in engine rpm in my Barikell MK8 120 Trowels?
    • L
      Louis MillerAug 26, 2025
      If you observe a drop in engine RPM in your Barikell Trowels, start by checking the air filter and clean or replace it if dirty. If the accelerator cable is broken or bent, replace it. For engine problems or a dirty carburetor, it is best to contact our technical service.
  • J
    James SmithAug 28, 2025
    How to fix blades that do not lift on Barikell Trowels?
    • E
      eryanAug 28, 2025
      If the blades on your Barikell Trowels do not lift, check the steel cord. If it's broken, replace the blade-lifting cord. Also, verify if the steel cord nut is missing and fit a new one if necessary. If the fork is broken, it will also need to be replaced.
  • O
    ogonzalezSep 1, 2025
    What to do if my Barikell MK8 120 float machine does not move forward and backward?
    • B
      Benjamin DennisSep 1, 2025
      If your Barikell float machine isn't moving forward or backward, examine the tie rod and replace it if broken. Check the fork pin; if it's broken or slipped off, replace the pin or fork. Also, ensure the bascule support isn't jammed by cleaning it.
  • M
    Michelle ScottSep 4, 2025
    Why does my Barikell Trowels float machine not steer left or right?
    • B
      Brandon WalkerSep 5, 2025
      If your Barikell float machine does not steer left or right, the issue might be with broken ball joints, which would need replacement. Alternatively, the rim supports could be broken, also requiring replacement. Another possibility is that the steering supports are out of place, in which case you should adjust them.
  • J
    Jason NelsonSep 8, 2025
    What to do if, when the engine is revved up, the rotors do not turn on my Barikell Trowels?
    • S
      Sherry GarciaSep 8, 2025
      If the rotors of your Barikell Trowels aren't turning when the engine is revved up, it might be due to slack or worn driving belts; tighten them or replace them. Another potential cause is a worn clutch lining, which would need to be replaced.

Barikell MK8 120 Specifications

General IconGeneral
BrandBarikell
ModelMK8 120
CategoryTrowels
LanguageEnglish