Page 8 =.%'#$*+(2*"/'>3$-#2.(-?'0/$"-$'*"//'@ABBBABCCADEFE8
Item 64996
GH=;IJ KL;MHINKO PHNOI;OHOQ;HGG;P!RJ
I$(-2.('G"4'Q+"2(''
QHVINKO\ S$"%'+$"Y&A)3#&'4.%W',/.Y$-'4+$('+"()/2(,'G"4'Q+"2(8
OKINQ;6''I.'0%$Y$(#')":",$'#.'G"4'Q+"2(?'do not tension hot chain.''R$#'*+"2('*../'5$9.%$'#$(-2.(2(,8
Check tension:
a. Before every use.
b. Often during first half hour of use.
c. Periodically during use.
1. Snap Test: Pull Saw Chain away from
bottom of Guide Bar, then let go. Saw Chain
should snap back to its original position,
solidly contacting bottom of Guide Bar.
2. Pull Saw Chain by hand around Guide Bar
several times, it should feel snug and
move freely around Guide Bar.
3. Adjust tension as necessary by tightening or
loosening Tensioning Screw, then repeating steps
1. and 2., until proper tension is achieved.
=2//'H3#.:"#2*'K2/$%'M$-$%Y.2%
OKINQ;6 I.'0%$Y$(#')":",$'#.'G"4'Q+"2(?'U%2Y$'!"%'"()'U%2Y$'G0%.*W$#?'W$$0'K2/$%'M$-$%Y.2%'93//8'''
U.'(.#'.0$%"#$'L./$'G"4'42#+.3#'.2/8''U.'(.#'03#'3-$)'.2/'2('M$-$%Y.2%8
O.#$6 Oil is automatically applied to
the Saw Chain during operation.
Fill Oiler Reservoir:
a. Before every use.
b. When oil level reaches MIN
mark on Oil Level Gauge.
1. Remove Oil Fill Cap.
2. Using funnel, fill tank with bar and
chain oil (sold separately).
3. Use clean cloth to remove excess oil.
4. Replace Oil Fill Cap and tighten.
H##"*+'G+.3/)$%'G#%"0
1. If desired, change location of Shoulder
Strap Connector by loosening Bolt, moving
Connector, then tightening Bolt securely.
2. Clip Shoulder Strap into hole on Connector.
H)X3-#'L./$'G"4'R$(,#+
1. With Pole Saw parallel to ground, move
Extension Lock to unlocked position.
2. Pull on motor housing to expose extension pole.
Pull out to desired length, then move Extension Lock
to locked position until it clicks into place.
R.*W$)
V(/.*W$)
=2,3%$'!6'';[#$(-2.('R.*W'L.-2#2.(-
SHMONOT\ I.'0%$Y$(#'-$%2.3-'2(X3%&?'
*+$*W';[#$(-2.('R.*W'9.%'#2,+#($--'5$9.%$'
$Y$%&'3-$'"()'0$%2.)2*"//&')3%2(,'3-$8''
N9';[#$(-2.('R.*W'/..-$(-'.%'L./$':.Y$:$(#'
2-'(.#$)'-#.0'3-2(,'2::$)2"#$/&?'#+$(6
a. Move Extension Lock to unlocked position.
b. Tighten Extension Lock Screw (64)
two revolutions.
c. Move Extension Lock to locked
position until it clicks into place.
d. Confirm that Pole is securely locked in
position and cannot extend or retract.
SHMONOT\''N9'L./$').$-'(.#'/.*W'2('0/"*$?'
2(-0$*#';[#$(-2.('R.*W8''U.'(.#'3-$'L./$'G"4'
29';[#$(-2.('R.*W'2-'4.%(?')":",$)?'.%'
*"((.#'.#+$%42-$'93(*#2.('0%.0$%/&8
To Next Page
Loading...