Bauer 1962E-B - Abrasive Cutting-Off Safety; Sanding Safety; Polishing Safety; Wire Brushing Safety

Page 8 For technical questions, please call 1-888-866-5797. Item 57003
Safety Warnings Specific for Abrasive Cutting-off Operations
1. Do not “jam” the cut-off wheel or apply
excessive pressure. Do not attempt to make
an excessive depth of cut.2YHUVWUHVVLQJWKH
ZKHHOLQFUHDVHVWKHORDGLQJDQGVXVFHSWLELOLW\
WRWZLVWLQJRUELQGLQJRIWKHZKHHOLQWKHFXWDQG
WKHSRVVLELOLW\RINLFNEDFNRUZKHHOEUHDNDJH
2. Do not position your body in line with and
behind the rotating wheel. When the wheel,
DWWKHSRLQWRIRSHUDWLRQLVPRYLQJDZD\IURP
\RXUERG\WKHSRVVLEOHNLFNEDFNPD\SURSHOWKH
VSLQQLQJZKHHODQGWKHSRZHUWRROGLUHFWO\DW\RX
3. When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while
the wheel is in motion otherwise kickback
may occur. Investigate and take corrective
DFWLRQWRHOLPLQDWHWKHFDXVHRIZKHHOELQGLQJ
4. Do not restart the cutting operation in
the workpiece. Let the wheel reach full
speed and carefully reenter the cut.
7KHZKHHOPD\ELQGZDONXSRUNLFNEDFNLIWKH
SRZHUWRROLVUHVWDUWHGLQWKHZRUNSLHFH
5. Support panels or any oversized
workpiece to minimize the risk of wheel
pinching and kickback./DUJHZRUNSLHFHV
WHQGWRVDJXQGHUWKHLURZQZHLJKW6XSSRUWV
PXVWEHSODFHGXQGHUWKHZRUNSLHFHQHDU
the line of cut and near the edge of the
ZRUNSLHFHRQERWKVLGHVRIWKHZKHHO
6. Use extra caution when making a “pocket cut”
into existing walls or other blind areas.
7KHSURWUXGLQJZKHHOPD\FXWJDVRUZDWHUSLSHV
HOHFWULFDOZLULQJRUREMHFWVWKDWFDQFDXVHNLFNEDFN
Safety Warnings Specific for Sanding Operations
Do not use excessively oversized sanding disc paper. Follow manufacturer’s recommendations
when selecting sanding paper./DUJHUVDQGLQJSDSHUH[WHQGLQJEH\RQGWKHVDQGLQJSDG
SUHVHQWVDODFHUDWLRQKD]DUGDQGPD\FDXVHVQDJJLQJWHDULQJRIWKHGLVFRUNLFNEDFN
Safety Warnings Specific for Polishing Operations
Do not allow any loose portion of the polishing bonnet or its attachment strings
to spin freely. Tuck away or trim any loose attachment strings./RRVHDQGVSLQQLQJ
DWWDFKPHQWVWULQJVFDQHQWDQJOH\RXUILQJHUVRUVQDJRQWKHZRUNSLHFH
Safety Warnings Specific for Wire Brushing Operations
1. Be aware that wire bristles are thrown by
the brush even during ordinary operation.
Do not overstress the wires by applying
excessive load to the brush.7KHZLUHEULVWOHV
FDQHDVLO\SHQHWUDWHOLJKWFORWKLQJDQGRUVNLQ
2. If the use of a guard is recommended for
wire brushing, do not allow any interference
of the wire wheel or brush with the guard.
:LUHZKHHORUEUXVKPD\H[SDQGLQGLDPHWHU
due to work load and centrifugal forces.
SAFETY OPERATION MAINTENANCESETUP