Bavarian Demon CORTEX User Manual

QUICKSTART-GUIDE
DE
VORBEREITUNG
RC-Anlage muss ugfertig
programmiert (eingeogen) sein.
Dual-Rate AUS.
ANSCHLUSS
Kanäle entsprechend Beschriftung
von Empfänger zu Servos durchschlei-
fen, d.h. Signaleingang A wird an
Ausgang A ausgegeben, usw,. Beispiel:
Kabelbaum A = Höhe am Empfänger
=> Höhenservo auf A stecken. Nicht
benötigte Kanäle frei lassen, aber
mind. A + B + AUX anschließen.
Die einadrigen Kabel müssen auf
„Impuls“ gesteckt werden.
EINBAULAGE
Wie abgebildet einbauen: Steckerseite
nach oben und in Flugrichtung. Auf
optimale Ausrichtung in allen 3 Achsen
achten. Andere Einbaulagen per PC
einstellbar.
SETUP
Jumper wie abgebildet einstecken,
dann einschalten. LED beobachten!
Hinweis: Achsen die nicht stabilisiert
werden sollen, einfach überspringen
(keinen Knüppelausschlag geben).
Knüppel neutral, warten...
Quer voll rechts, halten…
Quer voll links, halten…
Quer Mitte, Höhe drücken, halten…
Höhe ziehen, halten...
Höhe Mitte Seite rechts, halten…
Seite links, halten…
Seite Mitte, Fertig: erst Jumper
abziehen, dann ausschalten.
PREPARATION
Tx must be set ready to y.
Dual-Rate OFF.
CONNECTION
Use channels A-E to connect servos
with the corresponding Rx channel,
i.e. signal A is put out on servo port
A and so on. Example: cable A to Rx
= elevator from Rx => plug elevator
servo into servo port A.
Leave unused channels unplugged,
but connect at least A + B + AUX.
The single-core cables must be
plugged into „pulse“.
MOUNTING ORIENTATION
As shown in the picture: socket side
up and facing front. Insure a perfect
alignment to all 3 axis.
Other orientations available via PC.
EN
SETUP
Insert jumper, then power on.
Watch the LED!
Note: For not stabilising an axis,
simply skip the designated step by not
applying stick input.
Wait with sticks neutral...
Aileron right end and hold…
Aileron left end and hold...
Aileron neutral Elevator push and hold…
Elevator pull and hold…
Elevator neutral Rudder right and hold…
Rudder left and hold…
Rudder neutral, done: remove jumper,
then power off.
A
B
C
D
E
A
B
C
D
E
AUX
RX SERVO
JUMPER
LED

Bavarian Demon CORTEX Specifications

General

Brand	Bavarian Demon
Model	CORTEX
Category	Science Education products
Language	English

Summary

Preliminary Information

Operating Principle and Features

Explains the system's function, axes stabilization, and compatibility with fix wing aircrafts.

Mounting

Connecting Receivers

Details connecting conventional receivers via single channels or sum signal/satellites.

Connecting Servos

Describes connecting servos to CORTEX outputs A to E and handling non-stabilised channels.

Securing the CORTEX

Crucial installation position and use of adhesive foam pads for vibration damping.

Commissioning

Setup

Step-by-step guide for initial setup using a jumper and stick movements for axis calibration.

Switching On Flight Operation

How to start the system in normal operation after setup and initialisation indicators.

LED Signals

Explains the meaning of different LED flashing patterns for status and faults.

Gyro Channel and Activating Gyros

Adjusting gyro sensitivity and modes via the gyro channel in the transmitter.

Gyro Directional Test

Procedure to test servo response against model tilt for correct gyro direction.

Test Flight and Flying

Guidance on initial flights, setting sensitivity, and reducing expo for optimal performance.

Using Gyro Modes

Explanation of Normal Mode and Hold Mode functions and their applications.

Accessories

Accessory List

Lists available accessories such as foam tape, cable looms, and suppression hood.