EasyManua.ls Logo

BE&SCO Betamax 20 - User Manual

BE&SCO Betamax 20
80 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
WARNINGS
SHOWN WITH EXIT
CONVEYOR, WEDGE PRESS
AND WEDGE PRESS STAND
11-1-16
!
POWER FAILURE WARNING
IN CASE OF POWER FAILURE, TURN OFF GAS AND FOLLOW
SHUT DOWN PROCEDURES FOR OVEN.
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS
OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
WARNING
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR
MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH.
READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.
INSTRUCTIONS AND WARNING CONTAINED IN THIS MANUAL MUST
BE READ, UNDERSTOOD AND FOLLOWED.
POST IN A PROMINENT LOCATION INSTRUCTIONS TO BE FOLLOWED IN THE
EVENT USER SMELLS GAS. THIS INFORMATION SHALL BE OBTAINED BY
CONSULTING YOUR LOCAL GAS SUPPLIER. AT A MINIMUM:
TURN OFF GAS
EXTINGUISH ANY EXISTING FLAMES
CONTACT YOUR GAS SUPPLIER
IF YOUR GAS SUPPLIER CAN’T BE REACHED, CONTACT
LOCAL FIRE DEPARTMENT
Model 20 Betamax
Question and Answer IconNeed help?

Do you have a question about the BE&SCO Betamax 20 and is the answer not in the manual?

Summary

Safety Warnings

Power Failure Warning

Warning about turning off gas during power failure and following shutdown procedures.

Flammable Vapors and Gas Leak

Do not store flammable vapors; post gas leak instructions. Improper installation can cause damage or death.

General Precautions

Operational and Maintenance Safety

Keep clear of combustibles, ensure airflow, disconnect power before maintenance, use master switch for emergency shutdown.

Oven Placement Requirements

Placement Standards

Specific standards for unit placement regarding airflow, level ground, and distance from walls.

Installation Requirements

Electrical and Gas Compliance

Work must follow electrical and gas codes; details electrical specifications.

Natural Gas Specifications

Gas Properties and Orifices

Details natural gas properties, supply pressure, and burner orifice sizes.

Oven Control Panel

Control Panel Functions

Explains operation of switches, meters, and controls on the oven panel.

Wedge Press Control Panel

Control Panel Functions

Details controls and indicators on the wedge press panel for operation.

Temperature Adjustment

Adjusting Temperature Controller

Guide to changing temperature settings using the controller interface.

Oven Start-up Procedure

Start-up Flowchart

Step-by-step guide for safely starting the oven section, including ignition checks.

Shutdown Procedures

Oven and Press Shutdown

Steps for safely shutting down both the Wedge Press and the Oven sections.

Oven Troubleshooting

Common Oven Issues

Solutions for problems like no power, blown fuses, or open doors affecting operation.

Dough Preparation and Handling

Dough Making Process

Covers dough mixing, dividing, rounding, proofing, and thawing for optimal tortilla making.

Dough Making Troubleshooting

Dough Stickiness and Proofing Issues

Addresses sticky dough balls and proofing problems.

Tortilla Making Process

Tortilla Production Steps

Details the procedure for making tortillas, including dough ball preparation and machine operation.

Tortilla Making Troubleshooting

Tortilla Quality Issues

Solutions for problems like broken edges, grainy appearance, and inconsistent tortilla sizes.

Betamax Oven Cleaning

Cleaning Overview and Materials

Introduction to cleaning the oven and a list of required cleaning materials.

Oven Cleaning Safety

Cleaning Precautions

Essential safety measures before and during oven cleaning, including power and cooling.

Removing Stuck Tortilla

Stuck Tortilla Removal Procedure

Steps and precautions for safely removing a stuck tortilla from the wedge press.

Wedge Press Maintenance

Maintenance Procedures and Schedule

Covers greasing, part replacement, and maintenance schedule for the wedge press.

Oven Maintenance

Cone Bearing Maintenance

Details the maintenance schedule and procedures for the oven's cone bearing.

Wedge Press Maintenance Schedule

Preventative Maintenance Tasks

A schedule outlining daily, weekly, and 1500-hour maintenance tasks for the wedge press.

Wiring Diagram

VFD Wiring Diagram

Provides the updated wiring diagram for the machine with VFD integration.

Original Equipment Warranty

Warranty Terms and Conditions

Outlines the terms, limitations, and duration of the equipment warranty.

BE&SCO Betamax 20 Specifications

General IconGeneral
BrandBE&SCO
ModelBetamax 20
CategoryCommercial Food Equipment
LanguageEnglish