7
enter the working state The indicator light and nixie tube display can be changed from flashing
to normally on, and the ":" of the nixie tube will flash, and the nixie tube will display the working
time.
3
、柴火饭：
3. Firewood rice:
能自动判断米量，根据不同米类和米量煮饭，能最大限度的保留住米饭中的营养成分。工作
时，数码管显示跑马灯，进入倒计时十分时显示时间，工作完成后，蜂鸣器
“
嘀
”
五声停
1
秒，
自动进入保温程序，此功能
24
小时预约可调，但是不可设定烹调时间。
It can automatically judge the amount of rice. According to different types of rice and the
amount of rice cooking, it can maximize the retention of nutrients in rice. When working, the
digital tube displays the running lamp, enters the countdown and 10 minutes to display the time.
After the work is completed, the buzzer "beeps" for 1 second, and automatically enters the heat
preservation program. This function can be adjusted 24 hours for appointment, but the cooking
time cannot be set.
4
、快煮饭：
4. Quick cooking:
能自动判断米量，根据不同米类和米量煮饭，能最大限度的保留住米饭中的营养成分。工作
时，数码管显示跑马灯，进入倒计时五分时显示时间，工作完成后，蜂鸣器
“
嘀
”
五声停
1
秒，
自动进入保温程序，此功能不可预约，不可设定烹调时间。
It can automatically judge the amount of rice, according to different types of rice and the
amount of rice cooking, can maximize the retention of nutrients in rice. When working, the
digital tube displays the running lamp. When the countdown is five minutes, the time will be
displayed. After the work is finished, the buzzer "beeps" five times and stops for 1 second. The
function automatically enters the heat preservation program. This function cannot be reserved
or set the cooking time.
5
、开始
/
取消：
5. Start / cancel:
在待机状态下，选择某一功能或预约后，按下开始键，指示灯常亮
(
橙灯
)
，开始工作，在产品
工作过程中按此键，产品工作结束回到待机状态，数码管显示
“OFF”
。
In the standby mode, after selecting a function or appointment, press the start key, the indicator
light is always on (orange light), and starts to work. Press this key in the process of product work,
the product will return to the standby state after work, and the nixie tube will display "off".
6
、预约：
6. Appointment:
1.
使用条件：选定功能
10
秒内，按
“
约
”
键有效可预约的功能
)
，预约指示灯亮。
1. Conditions of use: select the function within 10 seconds, press the "appointment" key to
make an appointment), and the appointment indicator light is on.
2.
时间设置：按
“
预约
”
键进入，初始默认时间是
2
：
00
小时，最小设置值是
0
：
30
小时，最大设
置值是
24
：
00
小时，按
“
时间
”
键可以调节其时间。
2. Time setting: press the "appointment" key to enter. The initial default time is 2:00 hours, the
minimum setting value is 0:30 hours, and the maximum setting value is 24:00 hours. Press the
"time" key to adjust the time.
3.
预约取消：预约设置状态中，可再次按下
“
预约
”
键取消预约状态；预约工作中，可按
“
开始
/
取消
”
键取消预约回到待机状态。
To Next Page
Loading...