10 11ULTRATONE KXD15/KXD12 Quick Start Guide
ULTRATONE KXD15/KXD12 Controls
(EN) Step 2: Controls
(1) FX controls adjust the channel 1-4 signal
level at the input of the integrated
e ects processor.
(2) TO LINE OUT button routes the channel 4
signal to the LINE OUT output without e ects.
If you press both the TO MAIN and TO LINE
button, channel 4 will be equal to channels
1 - 3. The signal will be routed to the speakers
and the LINE OUT output including e ects.
(3) GRAPHIC EQ adjusts speci c frequencies in
the sound spectrum.
(4) MULTI-FX PROCESSOR unit adds a selected
sound e ect to any channels which have their
FX knob turned up. E ects include reverb,
chorus, delay, and pitch shifter.
(5) PROGRAM [PUSH] knob controls the e ects
settings. Rotate this knob to scroll through
e ects patches, and push to select a patch.
(6) FX RET knob controls the amount of e ects
added to the main mix.
(7) PHONES jack allows connection of
headphones using ¼" TRS stereo connectors.
(8) LEVEL controls adjust the signal level of
channels 1-4.
(9) TO MAIN routes the channel 4 signal to the
speakers without e ects. When disengaged,
the channel 4 signal normally routes to the
PHONES output without e ects.
(10) FBQ button activates the FBQ Feedback
Detection system. The frequencies causing
feedback are shown by the brightly lit fader
LEDs. Simply lower the level of the respective
frequency range until feedback disappears
and the LED goes out.
(11) CLIP LED lights when the signal from the
channel FX sends overloads the processor.
When the CLIP LED lights up please reduce the
e ects input signal by using the respective
FX control(s).
(12) SIG LED lights up when the e ects processor
receives an input signal.
(13) FX display shows the currently
selected preset.
(14) LEVEL control in the master section is used to
adjust the main output volume.
(15) SHAPE button applies a special lter to the
MASTER output to increase the sound’s clarity
and de nition in noisy environments.
(16) PHONES LEVEL control adjusts the
headphones output level.
(17) POWER switch turns the unit on or o .
You should always make sure that the POWER
switch is in the “O ” position when initially
connecting the unit to the mains.
(18) POWER SOURCE jack accepts the included IEC
power cable.
(19) LINE OUT connectors send out a post-EQ
audio signal to external devices. The XLR
connectors provide a balanced signal
suitable for connection to mixing or
recording consoles, while the ¼ " connectors
provide an unbalanced signal suitable for
additional ampli ers or other line-level
devices. Both XLR and ¼ " connectors may be
used simultaneously.
(20) STEREO LINK connection allows for true
stereo operation between two ULTRATONE
ampli ers. You can connect the OUT of one
ULTRATONE to the LINK IN of another keyboard
amp which then serves as slave to achieve a
true stereo sound.
(21) AUX IN connection accepts signals from CD
players, MP3 players or other sound sources
using RCA connectors.
(22) LINE inputs for channels 2-4 accept
unbalanced stereo signals through paired
¼" TS connectors. For mono input signals
please use the L (MONO) connector.
(23)
LINE/MIC input section for channel 1
features an additional XLR connection in
addition to dual ¼ " TS connectors. Use the
XLR connection for balanced signals from
microphones or other devices (+15 V phantom
power is available to power condenser
microphones). Both XLR and ¼ " connectors
can be used simultaneously, while the channel
1 LEVEL control adjusts the signal level for
both inputs.
To Next Page
Loading...
