Behringer XENYX QX1002USB User Manual

Quick Start Guide
17
XENYX QX1202USB/QX1002USB Controls
(16) PHONES/CONTROL ROOM – The stereo
PHONES jack (at the top of the connector
panel) is where you connect headphones.
The unbalanced CTRL ROOM OUT jacks carry
the summed eects and main mix signals, as
well as soloed channel signals. The PHONES/
CONTROL ROOM control adjusts the level of
both headphones and main monitor outputs.
(17) MAIN MIX – The MAIN OUT connectors are
balanced mono jacks. The main mix signal
appears here at a level of 0 dBu. The MAIN MIX
fader adjusts the volume of these outputs.
(18) CD/TAPE INPUT – The CD/TAPE INPUTs
are used to bring an external signal source
(e.g. CD player, tape deck, etc.) into the
console. They can also be used as a standard
stereo line input, so the output of a second
XENYX or BEHRINGER ULTRALINK PRO MX882
can be connected.
(19) CD/TAPE OUTPUT – These connectors are
wired in parallel with the MAIN OUT and carry
the main mix signal (unbalanced). Connect
the CD/TAPE OUTPUT to the inputs of your
recording device. The output level is adjusted
via the high-precision MAIN MIX fader.
(20) USB/2-TR TO PHONES/CTRL RM
button routes USB/2-Track playback to
PHONES/CTRL ROOM.
(21) USB/2-TR TO MAIN MIX button routes
USB/2-Track playback to MAIN MIX and mutes
the 2-TR OUT/USB recording signal.
(22) FX TO CTRL ROOM – If you want to monitor
only the FX send signal in your headphones
or monitor speaker(s), press the FX TO CTRL
switch. This mutes the main mix signal while
routing the FX SEND output to the monitor(s).
(23) +48 V – The +48 V LED lights up when
phantom power is on. The PHANTOM switch
activates the phantom power supply on the
XLR connectors of all mono channels.
(24) POWER – The POWER LED indicates that the
console is powered on.
(25) LEVEL INDICATOR – The high-precision
4-segment display accurately displays the
relevant signal level.
(26) SIGNAL and CLIP LED – The SIGNAL LED on
the eects module shows the presence of a
signal whose level is high enough. This LED
should always be on. However, make sure
that the CLIP LED lights up only sporadically.
If it is lit constantly, you are overdriving the
eects processor, which leads to unpleasant
distortion. If this occurs, turn the FX controls
down somewhat.
(27) PROGRAM – The PROGRAM control has two
functions: by turning the PROGRAM control,
you dial the number of an eect. The number
of the preset you just dialed up blinks in the
display. To conrm your selection, press the
PROGRAM control; the blinking stops.
(28) COMP – This knob adjusts the amount of
compression eect on the channel.
(29) PHANTOM – Press this button to send +48 V
of phantom power to the XLR inputs for use
with condenser microphones.
(30) USB CONNECTOR – Connect your mixer to a
computer using a standard USB cable.
(31) AC POWER IN – Connect the included power
cable here.
!
The mixer cannot be bus-powered via USB. Always
use the included power adapter to supply power to
the mixer.

Behringer XENYX QX1002USB Specifications

General

Channels quantity	10 channels
Digital sound processing	- bit
Total Harmonic Distortion (THD)	0.006 %
USB 2.0 ports quantity	4
DJ mixer	Yes
Product color	Black
Video capability	-
Equalizer bands quantity	3

Weight and Dimensions

Depth	248 mm
Width	195 mm
Height	50 mm
Weight	1100 g