Why my Beko DFN05211W does not start?
If your Beko Dishwasher doesn't start, several factors could be at play. First, ensure the power cable is securely plugged in. Then, check the fuses in your house. Make sure the water inlet tap is open and that the dishwasher door is fully closed. Finally, verify that you've pressed the On/Off button to turn the machine on.
How to fix Beko Dishwasher that leaves dishes not washed clean?
If your Beko Dishwasher leaves dishes unclean, consider these potential causes: * Make sure dishes are loaded properly, as described in the user manual. * Select a program with a higher temperature and cycle time. * Ensure impellers rotate freely and impeller holes aren't clogged. * Check and clean the filter system, ensuring correct installation. * Avoid overloading the baskets. * Store detergent properly and use a sufficient amount or switch to tablet detergents. * Check and refill rinse aid if needed, adjusting the setting accordingly. * Ensure the detergent dispenser lid is tightly closed.
What to do if water remains in Beko DFN05211W Dishwasher after cycle?
If your Beko Dishwasher leaves water at the end of the cycle, the filters may be clogged. Check and clean the filter system regularly. Alternatively, the discharge hose might be clogged or blocked. Inspect the discharge hose, remove any blockage, and re-insert it as shown in the user manual.
Why detergent remains in detergent dispenser of Beko Dishwasher?
If you find detergent remains in the dispenser of your Beko Dishwasher, ensure the dispenser is dry before adding detergent and add detergent shortly before starting the wash. Make sure dishes aren't blocking the dispenser lid and that the impeller holes are clear. Store powder detergent in a closed container in a non-humid place, or consider using tablet detergents.
How to prevent scratches on dishes in Beko Dishwasher?
If your Beko Dishwasher leaves dishes scratched, ensure you're not spilling salt when filling, as spilled salt can cause scratches. Make sure the salt reservoir lid is tightly closed and run a prewash cycle to remove any spilled salt. Also, check your water hardness setting and ensure it's appropriately set, and make sure that glassware is placed so it doesn't strike other dishes during washing.
Why there is a bad odor in my Beko DFN05211W?
If your Beko Dishwasher has a different odor, check if the filter system is clean and clean it regularly. Also, if you're not running the dishwasher immediately after loading, remove food remnants and run the Prewash program every 2 days. Don't completely close the door to prevent odor buildup. Consider using commercial odor removers or machine cleaners as well.
Why does foam form in my Beko DFN05211W Dishwasher?
If foam forms in your Beko Dishwasher, it may be because dishes were washed with hand-wash detergent but not rinsed before placing them in the machine. Hand-wash detergents don't contain antifoam. There's no need to hand-wash dishes beforehand; just remove coarse soil. Also, ensure rinse aid isn't spilled when filling and that the rinse aid reservoir lid is closed.
Why there is rust on dishes after Beko DFN05211W cycle?
If you notice rust, discoloration, or surface deterioration on dishes washed in your Beko Dishwasher, it could be due to several reasons. Salt leakage can cause deterioration, so avoid spilling salt and ensure the salt reservoir lid is tightly closed. Run a prewash cycle to remove any spilled salt. Also, remove salty food remnants before loading. Ensure your electrical installation is grounded to prevent static electricity. Avoid using intensive cleansers like bleach, and don't use metal items for unintended purposes. Low-quality stainless steel cutlery and already corroded items should not be washed in the dishwasher.
Why there are smear remains on glasses after Beko Dishwasher cycle?
If you see a milk-stain-like smear on glasses from your Beko Dishwasher, or a bluish/rainbow tint when held to the light, it could be due to excessive rinse aid. Try lowering the rinse aid setting and cleaning up any spills when refilling. Alternatively, soft water may be corroding the glass. Measure your water hardness and adjust the dishwasher setting accordingly. If your water is soft, avoid using salt and choose higher temperature programs. You might also consider using commercially available glass protective detergents.
General| Product colour | White |
|---|---|
| Type | Freestanding |
| Control type | Electronic |
| Noise Level | 49 dB |
| Number of Washing Programs | 5 |
| Drying System | Static |
| Depth | 60 cm |
| Height | 85 cm |
| Drying Performance | A |
| Cleaning Performance | A |
| Delay Start | Yes |
| Half Load Option | Yes |
| Programs | Eco, Intensive, Quick, Normal |
To Next Page
