How to fix a Beko Washer that does not drain water?
If your Beko Washer isn't draining water, it could be due to a clogged or twisted water drain hose, so you should clean or flatten the hose. Alternatively, the pump filter might be clogged, so you should clean the pump filter.
Why is my Beko Washer leaking water from the bottom?
If you notice water leaking from the bottom of your Beko Washer, it could be because the water drain hose is clogged or twisted, so clean or flatten the hose. Another possible cause is a clogged pump filter, so clean the pump filter.
Why won't my Beko Washer go to the spinning step?
Your Beko Washer might not switch to the spinning step due to several reasons. There might be an unbalanced load in the product, which activates the automatic unbalanced load detection system. The product will also not spin if water is not drained completely, so check the filter and the draining hose. Excessive foam might have occurred, activating the automatic foam absorption system because of too much detergent usage, so use the recommended amount of detergent.
Why is my Beko WMB 81243LW Washer not rinsing well?
Your Beko Washer might not be rinsing well if the amount, brand, and storage conditions of the detergent used are inappropriate, so use a detergent appropriate for the washing machine and your laundry, and keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures. Also, check if the detergent is put in the wrong compartment, and ensure it is in the correct one. A clogged pump filter or a folded drain hose can also cause rinsing issues, so check the filter and the drain hose.
What to do if the Beko WMB 81243LW Washer programme cannot be started?
If a programme cannot be started or selected on your Beko Washer, the product may have switched to self-protection mode due to a supply problem (line voltage, water pressure, etc.). To resolve this, press and hold the Start / Pause / Cancel button for 3 seconds to reset the product to factory settings.
What to do if my Beko WMB 81243LW Washer does not take water in?
If your Beko Washer isn't taking in water, there might be a few reasons: * The tap could be turned off, so ensure that you turn on the taps. * The water inlet hose might be bent, so flatten the hose. * The water inlet filter could be clogged, so clean the filter. * The loading door may be open, so close the door.
Why is my Beko WMB 81243LW vibrating and making noise?
Your Beko Washer might be vibrating or making noise due to several reasons: it might be standing unbalanced, so you should stabilize the product by adjusting the feet; a hard substance might have entered into the pump filter, so you should clean the pump filter; transportation safety bolts are not removed, so you should remove the transportation safety bolts; laundry quantity in the product might be too little, so you should add more laundry to the product; excessive laundry might be loaded in the product, so you should take out some of the laundry or distribute the load by hand to balance it; the product might be leaning on a rigid item, so you should ensure that the product is not leaning on anything.
Why does my Beko WMB 81243LW take longer than the specified time?
The washing cycle on your Beko Washer might be taking longer than usual due to several factors. Low water pressure can cause the product to wait until it takes in an adequate amount of water. Low voltage can prolong washing time. A low input water temperature can extend the time needed to heat the water. An increased number of rinses or amount of rinse water can also lengthen the cycle. Finally, excessive foam from too much detergent can activate the automatic foam absorption system.
How to reduce excessive foam in my Beko Washer?
Too much foam inside your Beko Washer can be caused by improper detergents, so use detergents appropriate for washing machines. It can also happen if you use an excessive amount of detergent, so use only a sufficient amount. Detergent stored under improper conditions may also cause too much foam, so store detergent in a closed and dry location, away from excessive heat. Some meshed laundry such as tulle may foam too much, so use smaller amounts of detergent for this type of item. Make sure that the detergent is put in the correct compartment. If softener is being taken early by the product, there may be a problem in the valves or in the detergent dispenser, and you should call the Authorized Service Agent.
How to prevent laundry from turning gray in my Beko WMB 81243LW?
To prevent laundry from turning gray in your Beko Washer, ensure you use the recommended amount of detergent appropriate for water hardness and the laundry. Avoid washing at low temperatures for extended periods, and select the proper temperature for the laundry. Using insufficient detergent with hard water can also cause graying, so use the recommended amount. Avoid using an excessive amount of detergent.
General| Washing Capacity | 8 kg |
|---|---|
| Spin Speed | 1200 rpm |
| Energy Efficiency Class | A+++ |
| Number of Programs | 15 |
| Noise Level (Spin) | 76 dB |
| Color | White |
Safety guidelines to prevent injury and property damage.
Precautions for safe use by or around children.
Guidelines for safe electrical connection and usage.
Warnings about hot surfaces on the appliance.
Information on waste electrical and electronic equipment disposal.
Details about recyclable packaging materials.
General description of the washing machine's parts.
List of items included in the product packaging.
Detailed technical data and performance metrics of the appliance.
Instructions and guidelines for installing the washing machine.
Steps and advice before starting a wash cycle.
How to use the washing machine's functions and programmes.
Procedures for keeping the appliance clean and in good condition.
To Next Page
