Need help?Do you have a question about the Bergsteiger CAPRI and is the answer not in the manual?
General| Type | Travel System |
|---|---|
| Seating Capacity | 1 |
| Harness Type | 5-point harness |
| Max Load Capacity | 15 kg |
| Foldable | Yes |
| Sun Canopy | Adjustable |
| Features | Adjustable Handlebar |
| Age Range | 0-3 years |
Crucial warnings for child safety: no unattended children, fire hazard, prohibited activities, packaging removal.
Specifies age suitability, maximum child weight, and requirements for baby seats.
Ensures proper assembly, brake engagement, pre-use checks, and safe folding procedures.
Details safety standards and recommends original accessories and spare parts.
Regular lubrication of moving parts extends pram life and eases folding.
Prompt replacement or repair of damaged screws and parts is essential.
Regularly check brakes, harnesses, wheels, locks, seat, and buckles for good condition.
Brake parts, wheels, and tyres are wear items needing replacement.
Avoid direct sunlight to prevent fabric bleaching.
Do not use the pram if it is not working properly or is damaged.
Instructions for tyre repair, inner tube replacement, and worn tyre replacement.
Dry wet parts, use multi-purpose spray for chassis protection against corrosion.
Treat chrome parts with protective spray during cold seasons to prevent corrosion.
Clean fabric and chassis with lukewarm water and mild soap using a soft cloth.
Do not wash the fabric in a washing machine; use a soft cloth only.
Avoid abrasive cleaners, chlorine agents, or spirits for cleaning.
Do not dry the pram in intense sunlight.
Rinse metal parts with water after beach use and dry thoroughly.
Details the main parts of the pram: chassis, carrycot, and various seat units.
Lists essential accessories like rain cover, diaper bag, insect net, and footmuff.
Instructions for forcefully sliding rear wheels onto their respective axles.
Important note to remove transport protection from axles before attaching wheels.
Procedure for removing wheels by pressing the lock button on the rim.
How to lock swivel wheels by aligning them and using the plastic lever.
The seat unit can be attached to the chassis in two different directions.
Seat unit inserts into elongated openings on the left and right sides of the chassis.
Release the seat unit by pulling two levers simultaneously in the longitudinal direction.
Adjust backrest by pulling the metal lever located under it.
Warning: Damage to the attachment may occur if the lever is not pressed.
Insert four lateral metal pins into guide rail holes, starting with front pins.
Lower attachment slowly to ensure rear pins snap into guide rails.
Secure attachment using the retaining clip mounted on the right side.
Attachment usable only after correct snapping in all 4 places and securing with the safety clip.
Adjust carrycot cover or recline flat by pressing the red button on the right side.
Release attachment by pressing the plastic lever downward until it locks.
Lever is located on the chassis where attachment's metal pins click into the frame rear.
Chassis has a lock on the left side to prevent unintentional folding.
Operate lock, press finger towards chassis, pull lock to body to collapse chassis.
Lists main pram parts: chassis, seat extension, safety bar, and accessories.
Lists baby accessories: soft changing bag and mosquito net.
Press rear axle with foot, pull handlebar up until lock clicks audibly.
Important: Ensure locking device is properly locked before using the pram.
Swivel handlebar rearward, then lower backrest fully.
Pull two locking levers upward to let the pram slide slowly downward.
Slide wheels forcefully over their respective axles to attach them.
Important: Remove transport protection from axles before attaching wheels.
Press locking knob and pull wheels off axles simultaneously for removal.
Adjust backrest by pulling the metal lever under it and pressing upward.
The backrest can be adjusted into three distinct positions.
Caution: Sitting position is unsuitable for infants under 6 months old.
Assemble by pressing support buttons and pushing bar ends over them simultaneously.
Alternative method: fasten one side first, then push the other side on.
Adjust footrest by pressing two knobs below and moving to desired position.
Pull footrest up until it locks to return it to the original position.
Adjust by pulling two side safety levers and swiveling bar to opposite side until locked.
Safety pins on both sides protect swivel handlebar from unintentional swiveling.
Lists main pram parts: chassis, seat extension, safety bar, and accessories.
Details the included shopping basket.
Secure pram with foot on rear axle, pull handlebar up until lock clicks audibly.
Important: Ensure locking device is properly locked before using the pram.
Swivel handlebar rearward and lower backrest fully before folding.
Pull two locking levers towards you to allow the pram to slide slowly downward.
Slide wheels onto axles while pressing locking knob towards axle.
Important: Remove transport protection from axles before attaching wheels.
Press locking knob and pull wheel off axle to remove.
Insert seat extension into safety bar sockets until plastic supports lock into place.
Use pushbuttons to attach fabric, securing the changing bag from slipping.
Assembly process is identical to that of the buggy bar.
Adjust backrest by pulling metal lever under it and pressing upward.
Backrest can be adjusted into three distinct positions.
Caution: Sitting position is unsuitable for infants under 6 months old.
Assemble by pressing support buttons and pushing bar ends over them simultaneously.
Alternative method: fasten one side first, then push the other side on.
Adjust by pulling two side safety levers and swiveling bar to opposite side until locked.
Safety pins on both sides protect swivel handlebar from unintentional swiveling.
Adjust footrest by pressing two knobs below and moving to desired position.
Pull footrest up until it locks to return it to the original position.
Details main pram parts: chassis, carrycot, seat unit, and pushchair attachment.
Lists the included diaper bag.
Secure pram with foot on rear axle, pull handlebar up until lock clicks audibly.
Important: Ensure locking device is properly locked before using the pram.
Swivel handlebar rearward and lower backrest fully before folding.
Pull two locking levers towards you to allow the pram to slide slowly downward.
Slide wheels onto axles while pressing locking knob towards axle.
Important: Remove transport protection from axles before attaching wheels.
Press locking knob and pull wheel off axle to remove.
Note: Activate hand-brake only when the pram has come to a complete stop.
After releasing brake, move pram back to ensure correct release and prevent plate damage.
The seat unit can be attached to the chassis in two different directions.
Seat unit inserts into elongated openings on the left and right sides of the chassis.
Release the seat unit by pulling two levers simultaneously in the longitudinal direction.
Adjust backrest by pulling metal lever under it.
Warning: Damage to attachment may occur if the lever is not pressed.
Insert four lateral metal pins into guide rail holes, starting with front pins.
Lower attachment slowly to ensure rear pins snap into guide rails.
Secure attachment using the retaining clip mounted on the right side.
Attachment usable only after correct snapping in all 4 places and securing with the safety clip.
Adjust carrycot cover or recline flat by pressing the red button on the right side.
Release attachment by pressing the plastic lever downward until it locks.
Lever is located on the chassis where attachment's metal pins click into the frame rear.
Chassis has a lock on the left side to prevent unintentional folding.
Operate lock, press finger towards chassis, pull lock to body to collapse chassis.
Seat unit meets ECE R44/04 standards, suitable for children up to 10 kg.
Ensure maximum protection by following instructions; note clearance for chassis placement.
Clearance prevents direct transmission of impacts from uneven surfaces to child.
Details the main seat unit, its release button, sunroof, cover, harness, and handle.
Explains the harness system, buckles, tensioning, and belt guides.
Includes information label, quick guide, support pillow, and warning label.
Ensures correct child placement, harness use, buckling, tensioning, and proper seating.
Covers individual length adjustment, placement, alignment, loosening, and tightening.
Tighten harness by pulling front part; ensure belt is not twisted and fits child snugly.
Pillow offers comfort and support; recommended use and care instructions.
Includes airbag warning, installation direction, seat position, and belt routing.
Details mechanism for adjusting handle to four positions.
Covers cleaning methods, hand washing, drying, and fabric removal/attachment.
Features accessories like footmuffs, parasols, and pram lights.
Lists practical accessories: organizer, adapter, and handmuffs.
Lists available spare parts including tyres, tubes, and other components.
To Next Page
