15
The cookpot symbol appears again when time of day = the calculated start time.
Af
ter the automatic programme has ended, the symbol “A” blinks.
The audible signal his heard and the cookpot symbol and the relay are switched off.
Minute minder
Select minute minder button and set required time with +/- button. As the time set elapses the symbol bell symbol is
displayed. After the time set has elapsed, the audible signal sounds.
Audible signal
The audible signal sounds at the end of a minute minder cycle or of a cooking programme for a period of 7 minutes. The
signal can be cancelled by pressing any function button. Pressing the “-“ button without having previously selected a
function the frequency of the signal changes. A selection from 3 possibilities can be made. The selected signal is audible
as long as time “-“ button is pressed.
Programme start and verification
A programme which has been set is carried out after setting the time required. The “time to run” can be verified at any
time by selecting the appropriate function.
Setting error identification
The setting is correct if time of day is in between the calculated cooking start and end times. If an error has been made,
this will be indicated by the audible signal and by the symbol “A” flashing. The faulty setting can be corrected by
changing one or booth functions.
Cancelling programme
A programme can be cancelled by selecting the manual function. After a programme which has been set comes to an
end, it is automatically cancelled.
A
BNORMAL OPERATION
Any of the following are considered to be abnormal operation and may require servicing:
• Yellow tipping of the burner flame. • Burners failing to remain alight.
• Sooting up of cooking utensils. • Burners extinguished by cupboard doors.
• Burners not igniting properly. • Gas valves, which are difficult to turn.
In case the appliance fails to operate correctly, contact Bertazzoni Service Center.
CLEANING THE APPLIANCE
Before cleaning the appliance, it should be disconnected from the power supply and turn off the main gas
feeder valve.
Cleaning the work surface:
Periodically clean the burner heads, the enamelled steel grids, the enamelled covers and the flame caps using warm
soapy water. Then those parts should be rinsed and thoroughly dried.
Any liquid that overflows from pots must always be removed using a rag.
If it becomes difficult to open or close a valve, do not force it, but immediately request the assistance of the
technical service personnel.
Cleaning the enamelled parts:
To maintain the original features of the enamelled parts they should be cleaned frequently with soapy water. Never use
abrasive powders. Do not leave acidic or alkaline substances on the enamelled parts (vinegar, lemon juice, salt, tomato
sauce, etc.) and do not wash the enamelled parts while they are still hot.
Cleaning the STAINLESS steel parts:
Clean the parts with soapy water and then dry them with a soft cloth. The shine is maintained by periodically using
special products that generally are found in the market. Never use abrasive powders.
Cleaning the burner flame caps:
Since the flame caps are resting on the burner, to clean them just remove them from their seat and wash them with
soapy water. After they have been thoroughly dried and having checked that the holes are not clogged, they can be
replaced in their proper position.
Cleaning the inside of the oven glass:
One of the features of the oven is the possibility of removing the interior glass simply by loosening the 2 screws B (fig.
36), to clean the inside surface of the glass(fig. 35). This operation should be carried out while the oven is cold and with a
damp cloth. Do not use abrasives.
Cleaning the inside of the oven:
To thoroughly clean the inside of the oven, it is recommended to disassemble the door by carefully following the
instructions described below. Insert the hook C (figure 37) into the hinged sector D. Put the door in a semi-open position
and using both hands pull it towards you until it is released from the attachment. To replace the door, do the opposite
making sure to insert the two sectors F correctly. In addition, the side shelves can be removed very easily, by loosening
the lock rings that attach them to the oven.
To Next Page
Loading...