How to turn on Beurer Massager?
First, ensure that the batteries are inserted correctly and have contact. Remember that the on/off button must be pressed and held down to switch the unit on. If it still doesn't work, replace the batteries. If problems persist, please contact customer service.
What to do if skin in treatment area becomes red using Beurer Massager?
Temporary skin reddening under the electrode is harmless because it is caused by a localised increase in blood flow. Discontinue the treatment immediately and wait until the skin condition has normalised. However, if the skin irritation persists and you feel itching or irritation, the cause may be an allergy to the surface of the electrode, and you should consult your doctor before continuing use.
Why no stimulation can be felt using Beurer Massager?
If you can't feel any stimulation, try increasing the pulse intensity incrementally. You can also press the on/off button to restart the program. Also, check the batteries, they may be almost empty. If so, replace them.
What to do if you feel unpleasant sensation from the electrodes of Beurer Massager?
If you feel an unpleasant sensation from the electrodes, it might be because the electrodes are poorly moistened. To fix this, switch off the unit, take off the belt, moisten the belt (electrodes) and your lower back, and then restart the program according to the manual.
What to do if no stimulation can be felt from Beurer Personal Care Products?
If you can't feel any stimulation from your Beurer Personal Care Product, try these steps: * Increase the pulse intensity incrementally. * Press the on/off button to restart the program. * Replace the batteries, as they may be almost empty.
What to do if I feel an unpleasant sensation from Beurer Personal Care Products electrodes?
If you feel an unpleasant sensation from the electrodes of your Beurer Personal Care Product, switch off the unit. Then, take off the belt, moisten both the belt's electrodes and your lower back. Finally, restart the program according to the manual.
What to do if the Beurer Health Care Products unit does not switch on?
If your Beurer Health Care Products unit doesn't turn on, ensure the batteries are correctly inserted and making contact. Remember to press and hold the ON/OFF button to power the unit. If it still fails to switch on, try replacing the batteries.
Why can't I feel any stimulation from my Beurer Health Care Products device?
If you're not feeling any stimulation from your Beurer Health Care Products device, try incrementally increasing the pulse intensity. You can also press the on/off button to restart the program. Also, if the batteries are almost empty, replace them.
What to do if the skin in the treatment area becomes red using Beurer Health Care Products?
If the skin in the treatment area becomes red while using Beurer Health Care Products, discontinue the treatment immediately and wait for the skin to return to normal. Temporary skin reddening under the electrode is harmless, as it may be due to increased blood flow. However, if skin irritation persists, and you feel itching or irritation, consult your doctor before continuing use.
How to fix an unpleasant sensation from the electrodes of Beurer Health Care Products?
If you experience an unpleasant sensation from the electrodes of your Beurer Health Care Products device, switch off the unit. Then, take off the belt, moisten the belt (electrodes) and your lower back, and restart the program according to the manual. This issue may arise if the electrodes are poorly moistened.
Explains how the EM38 unit provides pain relief using TENS technology.
Lists symbols used within the instruction manual for guidance.
Lists symbols found on the unit's identification plate.
Crucial safety advice regarding the use and handling of the unit.
Details critical safety measures and contraindications for using the unit.
Advises when medical consultation is necessary before using the device.
Instructions for preparing the unit and belt before the initial operation.
Guidelines for safe battery replacement and handling.
Details the components and functions of the control unit and its display.
Step-by-step guide on how to correctly wear the back pain belt.
Instructions on using the extension belt for a better fit.
Guidance on how to attach the control unit to the belt holder.
Procedure for replacing the batteries when indicated.
Provides context on the intended use of the back belt.
Details the available programs (A, B, C, D) and their settings.
Instructions on how to increase or decrease the stimulation intensity.
How to activate the keylock to prevent accidental intensity changes.
Steps to take if experiencing stinging or itching during use.
How to pause the current program and resume it later.
Instructions for safely cleaning the device and its belt.
Guidance on environmentally friendly disposal of the unit and batteries.
Solutions for problems like unit not switching on or no stimulation.
Details on belt size, weight, electrode size, and electrical parameters.
General| Form factor | Belt |
|---|---|
| Pulse width | 220 µs |
| Product color | Black, White |
| Intensity range | 11 - 100 mA |
| Pulse rate range | 2 - 110 Hz |
| Number of programs | 4 |
| Adjustable intensity | Yes |
| Battery type | AAA |
| Battery voltage | 1.5 V |
| Number of batteries supported | 3 |
| Display type | LCD |
Weight and Dimensions| Weight | 415 g |
|---|
To Next Page
