BGS technic 3264 User Manual

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0
F 56 essartS resukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni :liaM-E diehcsmeR 79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: 02196 720480
Fax.: 02196 7204820
mail@bgs-technic.de
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
Art. 3264
Air Die Grinder
SAFETY NOTES
1. Read these instructions carefully before using the item. The failure to
observe the following precautions can result in serious injury!
2. Use this tool NEVER near explosive items, materials, liquids or gases.
3. Disconnect the air grinder from air supply before changing attachments
or accessories.
4. Do not wear baggy or loose clothing when working with the air sander.
scarves, necklaces, bracelets, jewelry, etc. should not be worn while
working with the tool.
5. Tie together long hair and always wear safety glasses, gloves, hearing
protection and respiratory protection.
6. When operating, keep a secure and firm footing
7. Prior to the installation of accessories or maintaining the equipment,
disconnect the air supply.
8. Do not point the tool at yourself or other people. This can result in
serious injury.
9. Tighten all nuts, bolts and screws and make sure that your equipment
is in good working condition.
10. When there is a defect of the item, disconnect the tool directly from the
air. The air sander may be used again until after the test or repair.
11. Use only equipment that is suitable for pneumatic devices.
WARNING
Improper operation or maintenance of this product could result in serious injury and property damage.
Read and understand all warnings and operation instructions before using this equipment. When
using air tools, basic safety precautions should always be followed to reduce the risk of personal
injury.
WARRANTY
Please read these instructions carefully before use first time. For any questions about this product,
please contact your dealer.
We guarantee that all our products are free from defects in material. This warranty does not cover
damage due to improper use, lack of or improper maintenance and normal wear and tear. The
warranty does not cover also when the tool has been repaired by an unauthorized person, or
modified.

BGS technic 3264 Specifications

General

Brand	BGS technic
Model	3264
Category	Grinder
Language	English

Summary

Safety Notes

General Safety Precautions

Follow general safety rules for tool operation, including avoiding explosive environments and proper handling.

Personal Protective Equipment

Wear appropriate PPE such as safety glasses, gloves, and hearing protection; secure long hair.

Tool Handling and Maintenance

Ensure secure footing, disconnect air supply for changes, avoid pointing the tool at others, and check for defects.

Warning and Warranty Information

Product Warning

Read and understand all warnings and instructions to prevent serious injury or property damage.

Product Warranty

Warranty covers material defects but excludes damage from improper use, maintenance, or unauthorized repair.

Air Supply Requirements

Air Compressor and Pressure

Ensure correct compressor output (CFM) and use normal 90 PSI air pressure for optimal tool life.

Air Line and Hose Management

Drain water daily, clean the air inlet filter weekly, and use proper 1/4" I.D. or 3/8" I.D. hoses and fittings.

Operation Instructions

Tool Preparation and Accessory Fitting

Lubricate the tool, remove/re-install collet fixing cap correctly, and insert accessories rated for the tool's RPM.

Connecting Air Supply and Operation

Connect the air supply hose, set pressure to 90 PSI, and operate the throttle lever to control speed.

Care and Maintenance

Daily Lubrication

Lubricate the tool daily with air tool oil or equivalent; oil during continuous operation every 1-2 hours.

Storage and Disposal

Avoid humid environments, oil before storage, and recycle damaged tools responsibly.