EasyManua.ls Logo

BigSAT BS-S 67CR-M - User Manual

Default Icon
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
i
SAFETY PRECAUTION
CAUTION:
The lightning flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert the user
to "dangerous voltage"
and to prevent from a risk
of electric shock.
Warning:
To reduce the risk of
electric shock, don't open
the cabinet. Refer
servicing to qualified
personnel only.
The exclamation point
within an equilateral
triangle is intended to alert
the user to important
operating and
maintenance (servicing).
WARNING: Do not use this STB where contact with or immersion in water is a possibility. Do
not use near flower vase, washbowls, kitchen sinks, laundry tubs, swimming pools, etc.
WARNING: Do not put the candle or lamp stand on the cabinet; otherwise, there is the danger
of fire.
WARNING: The unit should be connected to a power supply only of the type described in the
operating instructions or as marked on the unit. If you are not sure of the type of power supply
(for example, 120 or
230 V) to your home, consult your local dealer or local power company.
WARNING: This product install diodes. Do not open the cabinet or touch any parts in the inner
mechanism. Consult your local dealer for technical service if the opening is required.
Note: To ensure proper use of this product, please read this User manual carefully and
retain for further reference.
Note: This product install diodes. Do not open the cabinet to avoid the unit direct exposure to
radiation.
Unit Cleaning: After the unit power is turned off, you can clean the cabinet, panel and remote
control with a soft cloth lightly moistened with a mild detergent solution.
Attachments: Never add any attachments and/or equipment without the manufacturer
consent; as such additions may result in the risk of fire, electric shock, or other personal injury.
Locating: Slots and openings in the cabinet are provided for ventilation to protect it from
overheating. Do not block these openings or allow them to be blocked by placing the STB on a
bed, sofa, or other similar surface, nor should it be placed over a radiator or heat register.
Power-Cord Protection: Place the power-supply cord out of the way, where it will not be
walked on. Please take special attentions to cords at plugs, convenience receptacles, and the
point where they exit from the unit.

Table of Contents

Questions and Answers

  • A
    Anita GarciaAug 12, 2025
    Why does my BigSAT BS-S 67CR-M say no signal?
    • L
      Louis BrownAug 13, 2025
      There might be several reasons why your BigSAT Receiver is showing 'No signal': * The signal level might be weak. * The LNB could be out of order. * The cable from the LNB might be incorrectly connected due to a short or open circuit. * The dish position could be aligned incorrectly.
  • N
    Nicole HernandezAug 16, 2025
    What to do if there is no picture on the screen from my BigSAT BS-S 67CR-M Receiver?
    • M
      marthayoungAug 17, 2025
      If there is no picture on the screen when using your BigSAT Receiver, consider the following possibilities: * The receiver might be in Standby mode. * The RCA jack may not be firmly connected to the video output port of the television. * The incorrect channel or video output is selected on the television. * The brightness level of your TV set is incorrectly defined.
  • A
    Amy BrownAug 20, 2025
    Why is my BigSAT BS-S 67CR-M not responding to the remote control?
    • C
      collierlisaAug 20, 2025
      If your BigSAT Receiver isn't responding to the remote control, it could be due to: * Dead or incorrectly inserted batteries in the remote control unit (RCU). * The RCU is not pointed in the right direction.
  • K
    kenneth15Aug 25, 2025
    How to fix no sound on my BigSAT BS-S 67CR-M?
    • B
      Barbara SosaAug 25, 2025
      If there is no sound from your BigSAT Receiver, check these potential causes: * The RCA cable might be connected incorrectly. * The volume level could be set too low. * The muting function might be active.
  • A
    Amber BellAug 28, 2025
    What to do if my BigSAT Receiver shows 'NO TV program'?
    • R
      Richard SchmidtAug 28, 2025
      If your BigSAT Receiver is on but there's no picture or sound (showing 'NO TV program'), it could be because: * The channel is not available. * The channel is scrambled.
  • D
    Dana WelchAug 31, 2025
    Why is the picture quality poor on my BigSAT BS-S 67CR-M?
    • D
      Dustin MurphySep 1, 2025
      Poor picture quality on your BigSAT Receiver could be due to a low signal strength.
  • M
    murraydavidSep 4, 2025
    What to do if there is no display on the LED Display Panel of my BigSAT Receiver?
    • L
      lambericSep 4, 2025
      If there is no display on the LED Display Panel of your BigSAT Receiver, the power cord might not be plugged in correctly.
  • B
    Brenda HubbardSep 7, 2025
    Why haven't the settings I made in the menu of my BigSAT Receiver changed?
    • S
      Susan DeckerSep 7, 2025
      If the settings you made in the menu of your BigSAT Receiver haven't changed, it's possible that the receiver lost power before it could enter standby mode. In this case, some of the settings saved by the user may be partially or fully deleted.

Summary

Safety Precautions

Electrical Safety Warnings

Details electrical shock hazards, voltage warnings, and cabinet opening restrictions.

General Usage Warnings

Covers warnings related to water, fire, power supply, and internal components.

Operational Safety Tips

Further Safety Guidelines

Object and Liquid Entry Prevention

Warns against inserting objects or spilling liquids into the unit.

Maintenance and Replacement Safety

Device Panel Overview

Rear Panel Connections

Details all rear panel ports: LOOP, LNB IN, ANT IN, TV OUT, VIDEO, AUDIO, RS232C, SCART.

System Connection Guide

Connecting to TV

Explains SCART, RCA, and RF cable connections to a television.

Connecting Audio Systems

Multi-Antenna Setup (DiSEqC)

Channel Management Features

TV Channel Manager

Channel Editing Functions

Skipping and Deleting Channels

Creating and Editing Channels

Channel Organization Tools

Sorting and Locking Channels

Channel Search and Utilities

Delete All Channels

Installation and Setup

Satellite Configuration

Detailed setup for satellite reception including satellite selection.

DiSEqC and Positioner

Configuration for DiSEqC switches and motor positioners.

LNB Type and 22 KHz Tone

Advanced Installation Settings

Polarity and TP Editing

Adjusting polarity and editing transponder (TP) parameters.

Channel Scanning

Channel Scanning and CA

Multi-Satellite Search

Conditional Access (CA) Setting

System Setup Navigation

Accessing System Settings

How to enter and navigate the main System Setup menu.

TV System Configuration

Display and Aspect Modes

Video Output and RF System

Time and Date Settings

Local Time Configuration

Timer Functionality

Setting Timers

OSD (On-Screen Display) Settings

Parental Control

Password Management

Setting and revising the parental control password.

Menu and Channel Locking

Enabling password protection for menu access and locked channels.

Tools Menu

Satellite Guide Assistance

Utilizing the satellite guide for antenna alignment assistance.

System Reset and Upgrade

Restoring Default Settings

Software Upgrade Methods

Instructions for upgrading receiver software via RS232 or OTA.

Troubleshooting Guide

Common Symptoms and Causes

Lists common issues like no signal, no picture/sound, and unresponsiveness.

Technical Specifications

General Specifications

Details system standard, channel storage, frequency, and LNB control.

A;V and Memory Specifications

Power and Physical Specifications

Connection Interfaces

Lists all available input and output connection ports.

BigSAT BS-S 67CR-M Specifications

General IconGeneral
BrandBigSAT
ModelBS-S 67CR-M
CategoryReceiver
LanguageEnglish