Billy Goat BC2600 Series

Questions and Answers

B
Benjamin MiddletonAug 16, 2025
Why won't my Billy Goat Brush Cutter engine start?
- F
  fhernandezAug 16, 2025
  If your Billy Goat Brush Cutter's engine won't start, there are several potential causes: * The throttle might be set to the Slow/Stop position, so move the throttle to the fast position. * You might be out of gasoline, so fill the gas tank. * The gasoline may be old or contaminated, so drain the gas tank and fill it with fresh gasoline. * The spark plug wire could be disconnected, so connect the spark plug wire. * The air cleaner might be dirty, so clean or replace the air cleaner.
B
Benjamin MedinaAug 19, 2025
What to do if my Billy Goat BC2600 won't cut well?
- T
  Tracy CampbellAug 19, 2025
  If your Billy Goat Brush Cutter isn't cutting well, consider these potential solutions: * Adjust the blade drive cable tension if it's incorrect. * Sharpen or replace the blade if it's dull (note: a new bolt will be needed if the blade is removed). * Unclog the deck if it's clogged. * Clear any excessive debris built up on or blocking the blade. * Check the engine RPM, as it might be set too low.
D
Duane AustinAug 21, 2025
What to do if the starter does not turn on my Billy Goat BC2600 Brush Cutter?
- A
  Ashlee RomeroAug 22, 2025
  If the starter on your Billy Goat Brush Cutter (electric start only) isn't turning, here are a few things to check: * The battery might be low or dead, so charge or replace it. * The battery cable could be disconnected or corroded, so clean and secure the battery terminals. * There might be a defective starter switch or wiring harness, which would need to be replaced. * The starter itself could be defective, requiring replacement.
A
Adam PhillipsAug 25, 2025
What to do if the blade brake will not engage on my Billy Goat BC2600?
- R
  Randy FoxAug 26, 2025
  If the blade brake won't engage on your Billy Goat Brush Cutter, the issue might be inadequate slack in the clutch cable, so adjust the clutch cable. Alternatively, the clutch might be worn or damaged, requiring replacement of the clutch/brake assembly.
A
Amanda AndersonAug 28, 2025
Why is my Billy Goat Brush Cutter vibrating abnormally?
- K
  katiefloresAug 28, 2025
  Abnormal vibrations in your Billy Goat Brush Cutter can stem from several issues. Check if the blade is loose or out of balance; tighten it or rebalance if necessary. Also, check the engine mounting bolts to ensure the engine isn't loose. A worn blade drive belt can also cause vibrations, so consider replacing it.
K
Kathleen PriceAug 31, 2025
Why does the belt slip or smoke on my Billy Goat BC2600?
- A
  Alex JenkinsAug 31, 2025
  If the belt on your Billy Goat Brush Cutter is slipping or smoking, it could be due to several reasons. The belt tension might be too low, so adjust it. Alternatively, the belt could be worn or stretched, requiring replacement. Finally, check the pulleys for wear or damage and replace them if necessary.
C
Christopher PayneSep 3, 2025
Why does the clutch slip or squeal on my Billy Goat BC2600?
- D
  Diane TorresSep 3, 2025
  If your Billy Goat Brush Cutter's clutch slips or squeals, it could be due to clutch cable tension being too low, so replace the spring on the idler arm. It's also possible that the clutch is worn or damaged, in which case you should replace the worn or defective clutch assembly parts.
G
Gregory RobinsonSep 6, 2025
What to do if the transaxle will not engage on my Billy Goat BC2600?
- S
  sharon42Sep 6, 2025
  If the transaxle won't engage on your Billy Goat Brush Cutter, first check if the clutch lever is properly engaging the clutch; if not, adjust the clutch cable. If that's not the issue, the clutch cable might be defective, requiring replacement. A worn or broken belt could also be the cause, so replace the belt if necessary.
G
georgedunlapSep 9, 2025
What to do if the transaxle will not disengage on my Billy Goat BC2600 Brush Cutter?
- S
  samanthasimonSep 9, 2025
  If the transaxle won't disengage on your Billy Goat Brush Cutter, the clutch cable might be out of adjustment, so adjust the clutch cable.
C
Cody MoralesSep 12, 2025
Why won't the engine turn over on my Billy Goat Brush Cutter?
- L
  Lynn CampbellSep 12, 2025
  If the engine won't turn over on your Billy Goat Brush Cutter, it could be due to a defective blade clutch, in which case you should replace the clutch. If that's not the issue, there may be an engine problem. Contact an authorized servicing dealer for your engine.