Billy Goat KV601SP User Manual (English)

Questions and Answers:

S
Savannah SmithAug 16, 2025
Why is my Billy Goat KV601SP Vacuum Cleaner not picking up leaves well?
- M
  Michael ClementsAug 16, 2025
  If your Billy Goat Vacuum Cleaner isn't vacuuming well, consider these potential causes: * The debris bag might be dirty, requiring a cleaning (shaking or washing). * The hose kit cap could be missing. * The nozzle or exhaust might be clogged, needing unclogging. * There might be too much debris, restricting airflow. * The nozzle height may be improperly adjusted; adjust it closer to the debris.
P
Paula HortonAug 19, 2025
How to start a Billy Goat KV601SP that won't start?
- I
  iancareyAug 19, 2025
  If your Billy Goat Vacuum Cleaner engine won't start, check the following: * Ensure the throttle is not in the off position. * Confirm the engine is in full choke position. * Make sure there's gasoline in the tank, and that it's not old or bad. * Ensure the spark plug wire is connected. * Check if the air cleaner is dirty and clean or replace it if necessary.
T
Timothy LoveAug 22, 2025
Why is my Billy Goat KV601SP vibrating so much?
- C
  connormcdanielAug 22, 2025
  Abnormal vibration in your Billy Goat Vacuum Cleaner may be due to a loose or out-of-balance impeller, or a loose engine. Check the impeller and replace it if required. Also, check the engine.
S
shannongrahamAug 26, 2025
What to do if Billy Goat KV601SP Vacuum Cleaner nozzle scrapes the ground?
- Q
  qwhiteAug 26, 2025
  If the nozzle of your Billy Goat Vacuum Cleaner scrapes the ground even at the highest setting, it's likely that the nozzle height is out of adjustment. Adjust the nozzle height.
D
Daniel BellAug 28, 2025
Why is my Billy Goat Vacuum Cleaner not self-propelled?
- N
  Nichole CardenasAug 28, 2025
  If your Billy Goat Vacuum Cleaner is not self-propelling, make sure the drive bail is engaged. Also, check the drive belt, the drive clutch cable, and the drive chain.
T
tonyagrayAug 31, 2025
What causes a Billy Goat KV601SP Vacuum Cleaner self-propelled drive to not release?
- D
  Danny BanksAug 31, 2025
  If your Billy Goat Vacuum Cleaner's self-propelled drive won't release, the drive clutch cable adjustment may be improper, or the cable could be kinked. Check the drive clutch cable.
L
Laura BrooksSep 3, 2025
How to fix a noisy chain on a Billy Goat KV601SP?
- N
  Natasha SmithSep 3, 2025
  If the chain on your Billy Goat Vacuum Cleaner is noisy or broken, it could be due to a lack of lubrication, chain misalignment, or tension issues. Lubricate the chain and check the drive chain.
R
raymondjohnsonSep 6, 2025
Why is my Billy Goat Vacuum Cleaner bag producing so much dust?
- A
  ahuntSep 6, 2025
  If too much dust is coming from the bag of your Billy Goat Vacuum Cleaner, it may be due to vacuuming very dry, brittle, or small debris. Consider switching to a felt bag.
K
Kim EllisSep 9, 2025
What to do if Billy Goat KV601SP engine is locked?
- J
  Jessica ThomasSep 9, 2025
  If the engine of your Billy Goat Vacuum Cleaner is locked and won't pull over, it might be due to debris locked in the impeller or an engine problem. See page 7. Contact an engine service dealer for engine problems.
D
Diana AguilarSep 12, 2025
How to make Billy Goat KV601SP Vacuum Cleaner go backwards?
- J
  Jacob OliverSep 12, 2025
  To allow the Billy Goat Vacuum Cleaner unit to free-wheel backwards, push the unit slightly forward.