This document is an owner's manual for a BILT HARD 20-inch oscillation pedestal fan, identified by SKUs HFC-0503 and HFC-0504. It provides essential information for safe operation, assembly, usage, servicing, and maintenance of the fan.
Function Description:
The BILT HARD 20-inch oscillation pedestal fan is designed to provide air movement for indoor use. It features adjustable speed settings and an oscillation function to distribute air across a wider area. The fan is intended for general air circulation in residential or light commercial indoor environments.
Important Technical Specifications:
While specific power ratings (e.g., wattage, voltage) are not explicitly detailed in the provided pages, the manual mentions a replacement fuse specification: "a 5 Amp 125V Fuse." This indicates the fan operates on a 125V electrical system and has a maximum current draw of 5 Amps, implying a maximum power consumption of approximately 625 Watts (125V * 5A). The fan incorporates a thermostat that automatically shuts off the motor if it overheats to 135°C, serving as a safety feature. The fan's size is specified as 20 inches, referring to the diameter of its blades or grille.
Usage Features:
The fan offers several user-friendly features:
- Speed Control: The fan has a speed switch located at the back of the fan, allowing users to select between Low, Medium, and High speeds to achieve the desired air movement.
- Oscillation Control: An oscillation function is available, controlled by a rocker switch on the fan motor housing. This allows the fan head to sweep from side to side, distributing air over a broader range.
- Adjustable Height: Although not explicitly detailed in the "ASSEMBLY INSTRUCTION" text, the presence of an "Inner pole" (11) and "Outer pole" (13) in the assembly diagram, along with instructions to "Loosen the extension pole nut onto the outer pole" and "Thread extension pole nut onto threads of inner pole," strongly suggests that the fan's height is adjustable. The "Neck" (10) also implies adjustability for the fan head's angle.
- Safety Thermostat: A built-in thermostat automatically shuts off the fan if the motor overheats to 135°C, preventing damage and potential hazards. If this occurs, the user is instructed to unplug the fan immediately.
Maintenance Features:
The manual outlines clear procedures for both servicing and routine care:
- Fuse Replacement: The fan is equipped with a replaceable fuse located within the plug. The manual provides detailed instructions for safely opening the fuse cover, removing the old fuse, and inserting a new 5 Amp 125V fuse using a small flat screwdriver. Emphasized safety precautions include not forcing the door and ensuring the fuse is properly situated.
- Cleaning:
- General Cleaning: Before cleaning, the fan must be unplugged. Users are advised to slightly moisten a soft cloth and wipe off the fan's surface.
- Grille Cleaning: To remove dust from the grille, a vacuum cleaner can be used. Alternatively, the front grille can be removed by unscrewing a securing screw on its edge with a screwdriver, allowing for more thorough cleaning. After cleaning, the grille must be remounted and the securing screw fastened.
- Prohibitions: Crucially, the manual warns against using water directly on metal surfaces, immersing the fan or any wires in water, or using the fan without the guard in place.
Assembly Instructions:
The fan requires simple assembly, detailed in 8 steps with accompanying figures (Fig.1 to Fig.10):
- Base and Outer Pole Assembly: Insert the outer pole into the base, align screw holes, insert screws, and tighten with nuts from underneath.
- Extension Pole Nut Adjustment: Loosen the extension pole nut on the outer pole.
- Cap Insertion: Insert the decorative cap through the outer pole.
- Inner Pole and Extension Nut: Thread the extension pole nut onto the inner pole.
- Motor Housing Attachment: Insert the fan motor housing into the inner pole and securely tighten the neck set screw.
- Rear Guard Assembly: Remove four mounting screws from the motor housing, then attach the rear guard using these screws and tighten them securely.
- Blade Attachment: Place the fan blade onto the motor shaft and tighten it securely with the set screw on the flat surface of the shaft.
- Front Guard Attachment: Attach the front guard to the rear guard, ensuring the hook clip is centered at the top above the wire handle. Press the remaining guard clips onto the rear guard to securely attach the front guard. The manual explicitly states: "Do not operate fan without guard in the place."
The manual includes a comprehensive list of safety warnings and cautions to prevent injury or damage:
- General Safety: Read all instructions before operation. Unplug the fan before moving or maintenance. Do not touch with wet hands. Only qualified electricians should disassemble or repair. Unplug when not in use. Do not unplug by pulling the cord.
- Cord and Plug Safety: Do not use if the cord or plug is damaged; it must be replaced by the manufacturer or qualified personnel. Do not use with an extension cord.
- Environmental Restrictions: Do not use near fires. Do not use outdoors; it is designed for indoor use only.
- Physical Safety: Do not insert hands or other objects into the grille or movable parts. Do not use with solid-state speed control devices.
- Child Safety: Not intended for use by people (including children) with reduced physical, sensory, or mental capabilities unless supervised or instructed. Supervise children to ensure they do not play with the fan.
- Maintenance Safety: Unplug before cleaning. Do not immerse the fan. Ensure the guard is fitted before starting.
Need help?
To Next Page
General