What does it mean if my Binder ULTRA.Guard UF V 500 Freezer temperature display shows “- - - - “ or “->” Messages alternating: Inner temp. sensor and Safety control sensor?
If your Binder Freezer's temperature display shows “- - - - “ or “->” with alternating messages for the inner temp. sensor and safety control sensor, it means both sensors are defective, and refrigeration is permanently on. Contact BINDER service.
What to do if alarm message A41 appears on Binder ULTRA.Guard UF V 500?
If you receive alarm message A41 on your Binder freezer, it indicates the cooling cycle has been operating permanently for more than 72 hours. Here's what to check: * Ensure the door is shut tightly. * Check for frost on the door gasket and defrost it with an ice scraper if needed. * Open the door less frequently. * Verify that the temperature set-point is correctly set on the controller. Additionally, consider if the installation place is too warm or if too warm or a large amount of material was introduced into the freezer. If so, select a cooler location or cool down the material and load smaller portions. It's also possible that the controller requires calibration and adjustment.
Why is my Binder Freezer not refrigerating well?
If your Binder freezer isn't refrigerating properly, first ensure the temperature set-point is correctly set on the controller. Check if the ambient temperature is too high (above 32 °C) and, if so, select a cooler place for installation. Also, reduce any external heat load affecting the freezer.
What does alarm message A52 on Binder ULTRA.Guard UF V 500 Freezer mean?
Alarm message A52 on your Binder freezer indicates a problem with the condenser. This can be due to a soiled condenser air filter or a soiled condenser. Ensure to clean the condenser air filter. Also, make sure the ventilation slots are not blocked, ensuring free air access to the device at the front and bottom.
What does it mean if my Binder ULTRA.Guard UF V 500 Freezer displays alarm message “Safety control sensor”?
If your Binder Freezer displays the alarm message “Safety control sensor”, it indicates that the safety controller temperature sensor is defective. Operation is temporarily possible. Contact BINDER service.
How to access menu functions on Binder ULTRA.Guard UF V 500?
If menu functions are not available on your Binder Freezer, it may be due to the current authorization level. Log in with the required higher authorization.
What to do if my Binder ULTRA.Guard UF V 500 Freezer displays alarm message “Condenser temp.”?
If your Binder Freezer shows the alarm message “Condenser temp.”, consider the following: * The condenser air filter may be soiled: Clean or replace the condenser air filter. * The condenser itself might be dirty: Clean the condenser. * Ventilation slots could be blocked: Ensure free air access to the device at the front and bottom. * The installation place might be too hot: Select a cooler location or contact BINDER service. * The chamber might be too close to the wall: Install or check the spacers.
What to do if Binder ULTRA.Guard UF V 500 Freezer has no or too low refrigerating performance?
If your Binder Freezer isn't refrigerating well, check these potential causes: * The temperature set-point may not be set correctly on the controller: Set the temperature set-point correctly. * The ambient temperature might be too high (above 32 °C): Select a cooler place of installation. * There may be too much external heat load: Reduce the heat load. For other potential causes, such as a defective Pt 100 sensor, defective refrigerating system, defective semiconductor relay, compressor not switched on, or not enough refrigerant, contact BINDER service.
Why I cannot close the door of my Binder ULTRA.Guard UF V 500?
If the door of your Binder freezer cannot be closed, it may be because the door was pressed too shortly (less than 2 seconds) and opened immediately after, which triggered the automatic door mechanism and now prevents closing the door again.
What to do if my Binder ULTRA.Guard UF V 500 keypad is not working?
If you cannot make entries to the controller keypad on your Binder freezer, it's likely that the keyboard locking is activated. Unlock the keyboard locking.
To Next Page
General