Bird b gone Bird Spider 360 User Manual

Installation Instructions
800.392.6915 | www.birdbgone.com | made in the USA
Thank you for purchasing the Bird•B•Gone
®
Bird Spider
360°™. For best results please read these instructions
before using and retain them for future reference.
Bird Spider 360°™ Overview:
Bird Spiders are stand alone physical deterrents used to
scare large birds from landing. The Bird Spiders “arms”
bounce and sway in the wind creating a visual distraction
zone that birds will not want to come near. Bird Spiders will
spin and sway in the wind, creating a visual distraction zone.
Birds will not want to come near the area being treated.
Every Bird Spider comes with a square weather-proof PVC
base with inserts (holes) for screwing or gluing down.
Gluing down base: Apply a construction grade adhesive to the
underside of the base, and apply to affected area. YOU MUST
ASSURE ALL HOLES ARE SEALED TO PREVENT MOISTURE /
WATER FROM ENTERING!
Screwing down base: This should be done whenever possible,
using self tapping screws. Make sure you do not damage
equipment (lights, A/C units, rooftops, etc.) when drilling or
screwing!
1. Ensure mounting surface is clean of bird feces and
debris before installing any bird deterrent, including the
Bird Spider 360°. Use Microcide SQ™ or a 10% bleach or
ammonia solution to disinfect the area.
2. Select the appropriate Bird Spider 360° (2’, 4’, 6’ or 8’)
depending on the surface of coverage. It is important
that the “tips” of the arms extend several inches over the
outside surface(s).
3. Stainless Steel arms must have room to spin and move
with the air. Do not mount Bird Spider 360° in an area
where the arms will be suppressed from movement or
blocked by walls.
4. Bird Spider 360° arm tips should be no more than 2-3”
above mounting surface.
5. If the Bird Spider 360° requires gluing for the installation,
the PVC adapter must be used.
6. If installing more than one Bird Spider 360° in a row, be
sure that they are installed 6-8” from arm tip-to-arm tip
(not base-to-base).
Need help? Contact Bird•B•Gone
®
, Inc. via telephone at
800.392.6915 or via email at nobirds@birdbgone.com.
Bird Spider 360°
TM
Make sure ends of rods
extend beyond edge of area
to be covered.
Bird Spider 360° arm “tips”
should overhang mounting
surface by at least 2”.
DO NOT GLUE THE BOTTOM OF THE BASE UNIT WITHOUT
INSTALLING THE PVC BASE.
Bird•B•Gone
®
recommends the use of SikaFlex and
Eclectic E6100 brand adhesives for best adhesion.

Bird b gone Bird Spider 360 Specifications

General

Brand	Bird b gone
Model	Bird Spider 360
Category	Accessories
Language	English

Summary

Bird Spider 360 Installation Overview

Gluing Down Base

Instructions for applying construction grade adhesive to the base, ensuring all holes are sealed to prevent moisture entry.

Screwing Down Base

Guidance on using self-tapping screws for installation, advising to avoid damaging equipment during the process.

General Installation Guidelines

Arm Movement and Height

Ensure arms have room to spin and are positioned 2-3" above the mounting surface.

PVC Adapter for Gluing

Use the PVC adapter when gluing the Bird Spider 360° base unit.

Spacing Multiple Units

Install multiple Bird Spiders 6-8" from arm tip-to-arm tip.

Boat Adaptation

Boat Base Attachment

Attach the Bird Spider 360° Base directly to the Boat Base, do not use the PVC attachment first.

Sandbag Base Attachment

Use Sandbag Base on boats, attach directly, and always secure it despite its weight.

Railing Mount Attachment

Secure the Bird Spider 360° to railings up to 1 7/8" thick for easy removal and stowage.