◈ Information
This installation guide contains quick information required for the product installation.
Please refer to the Software and Documents provided on the Download section of the
BIXOLON Website(http://www.bixolon.com) for more information on how to setup.
1. Manual: User’s Manual, Code Table, Control Commands, Software manuals
2. Driver: Windows Driver, OPOS, JPOS, CUPS(Linux, Mac), VCOM(USB, Ethernet)
3. SDK: UPOS SDK(iOS, Android)
4. Utility: Unified POS Utility, Net Configuration Tool, Android Utility, iOS Utility
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Components
SRP-330II/332II
Cable cover
Paper Roll
Procuct Installation CDProcuct Installation CD
CD
Installation Guide
2” Partition USB A-B Cable
AC/DC Adaptor
Power cord
◈ Cable Connection
1. Turn off the printer and peripheral devices.
2. Connect the power cord to the adapter and connect the adapter to the power supply
connector of the printer.
3. Check the type of the interfaces at the back of the printer(Serial, Dual Serial, USB,
Ethernet, Parallel) and connect the interface cable.
4. Connect the drawer kick-out cable to the drawer kick-out connector of the printer.
※ Do not use an adapter that was not supplied with the printer.
◈ Installing Paper Roll
1. Press the Cover-Open button to open the cover.
2. Insert new roll paper in the correct direction.
3. Pull the paper out slightly and close the cover.
※ Note
When closing the cover, press down on the center
of the cover to ensure that the paper is in contact
with the roller.
Printing quality may not be optimum if
recommended paper is not used.
(Refer to the User's Manual.)
◈ Using Control Panel
• POWER LED
The POWER light is on whenever the printer is on.
• ERROR LED
This indicates an error.
• PAPER LED
This light indicates the near end of the paper roll. Install a new paper
roll and the printer will continue printing. When the light blinks, it
indicates the self-test printing standby state or macro execution Standby
state when the macro execution command is used.
• FEED Button
Press the FEED button once to advance paper one line. You can also
hold down the FEED button to feed paper continuously.
◈ Mounting 2” Partition
Hang the partition at the front and press down the rear to mount the 2” partition as shown in
the picture.
※ Caution
After using 2"(58mm) paper roll, do not replace it with 3"(79.5±0.5mm) paper roll.
◈ DIP switch setting
DIP switch setting must be done while the printer is turned off.
Changes during power on are not recognized.
1. Serial / Dual Serial Interface Settings
• DIP Switch 1
Switch Function ON OFF Default
1-1 Auto Cutter Control Disable Enable OFF
1-2 Flow Control XON/XOFF DTR/DSR OFF
1-3 Data Length 7 bits 8 bits OFF
1-4 Parity Check Yes No OFF
1-5 Parity Selection EVEN ODD OFF
1-6
Baud Rate Selection(bps) Refer to the following Table 1
OFF
1-7 ON
1-8 OFF
• Table 1 – Baud Rate(bps) Selection
Transmission Speed 1-6 1-7 1-8 Default
2400 ON OFF OFF
9600
4800 ON OFF ON
9600 OFF ON OFF
19200 OFF OFF OFF
38400 OFF ON ON
57600 OFF OFF ON
115200 ON ON ON
2. Parallel / Ethernet / USB Interface Settings
• DIP Switch 1
Switch Function ON OFF Default
1-1 Auto Cutter Control Disable Enable OFF
1-2 Reserved - - OFF
1-3 Reserved - - OFF
1-4 Reserved - - OFF
1-5 Reserved - - OFF
1-6 Reserved - - OFF
1-7 Reserved - - ON
1-8 Reserved - - OFF
◈ Print Density(Virtual Memory Switch)
Speed
Print Density
Print Density
(Virtual Memory Switch)
Light
Dark
4(High) 1 2 3 4 Level 1
3 5 6 7 8 Level 2
2 9 10 11 12 Level 3
1(Low) 12 13 14 16 Level 4
※ It is recommended to select Unified POS Utility or Self-Test mode to change print
density using the Virtual Memory Switch.
◈ Self-Test
1. Check whether the paper is inserted correctly.
2. Turn on the printer while depressing the Feed button. Self-diagnostics will begin.
3. The printer prints the current status of the printer such as the version of the ROM and DIP
switch setting.
4. The printer prints the current status and stops after printing the following statement.
(PAPER indicator keeps blinking.)
SELF-TEST PRINTING.
SELECT MODES BY PRESSING FEED BUTTON.
Continuous SELF-TEST : Less than 1 second
VMSM Selection : 1second or more
5. Press the FEED button for less than 1 second to perform “Continuous SELF-TEST”.
Hold down the FEED button for 1 second or longer to perform “VMSM Selection”.
1) Self-Test
1-1) If you press the FEED button for less than 1 second, the printer will print in the
preset character type.
1-2) The self-test completes automatically and cuts the paper after printing the following
line.
*** COMPLETED ***
1-3) The printer goes into standby mode when the self-test is complete.
Printer Installation Guide & Safet
To Next Page
Need help?
General