10
ENGLISH
(Original instructions)
Warning! Do not use edge grinding/cutting wheels for surface
grinding applications if the wheel label has forbidden such use
because these wheels are not designed for side
pressures encountered with surface grinding. Wheel breakage
and serious personal injury may result.
Fitting and removing sanding discs (g. D & E)
For sanding, a backing pad is required. The backing pad is
available from your BLACK+DECKER dealer as an accessory.
Fitting
u Place the inner ange (10) onto the spindle (5) as shown
(g. E). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the backing pad (15) onto the spindle.
u Place the sanding disc (16) onto the backing pad.
u Place the outer ange (13) onto the spindle with the raised
centre facing away from the disc.
u Keep the spindle lock (2) depressed and tighten the outer
ange using the two-pin spanner (14) (g. D). Make sure
that the outer ange is tted correctly and that the disc is
clamped tightly.
Removing
u Keep the spindle lock (2) depressed and loosen the outer
ange (13) using the two-pin spanner (14) (g. D).
u Remove the outer ange (13), the sanding disc (16) and
the backing pad (15).
Surface nishing with sanding discs
u Allow the tool to reach full speed before touching the tool
to the work surface.
u Apply minimum pressure to work surface, allowing the tool
to operate at high speed. Sanding rate is greatest when
the tool operates at high speed.
u Maintain a 5˚ to 10˚ angle between the tool and work
surface as shown in gure G.
u Continuously move the tool in a forward and back motion
to avoid creating gouges in the work surface.
u Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before laying it down.
Using sanding backing pads
Always choose the proper grit sanding discs for your
application. Sanding discs are available in various grits.
Coarse grits yield faster material removal rates and a rougher
nish. Finer grits yield slower material removal and a
smoother nish.
Begin with coarse grit discs for fast, rough material removal.
Move to a medium grit paper and nish with a ne grit disc for
optimal nish.
u Coarse = 16 - 30 grit.
u Medium = 36 - 80 grit.
u Fine Finishing = 100 - 120 grit.
u Very Fine Finishing = 150 - 180 grit.
u Allow the tool to reach full speed before touching tool to
the work surface.
u Apply minimum pressure to work surface, allowing the tool
to operate at high speed. Sanding rate is greatest
when the tool operates at high speed.
u Maintain a 5˚ to 10˚ angle between the tool and work
surface as shown in gure H. The sanding disc should
contact approximately 25mm of work surface.
u Move the tool constantly in a straight line to prevent
burning and swirling of work surface. Allowing the tool to
rest on the work surface without moving, or moving the
tool in a circular motion causes burning and swirling marks
on the work surface.
u Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before laying it down.
Precautions to take when sanding paint
u Sanding of lead based paint is NOT RECOMMENDED
due to the difculty of controlling the contaminated dust.
The greatest danger of lead poisoning is to children and
pregnant women.
u Since it is difcult to identify whether or not a paint
contains lead without a chemical analysis, we recommend
the following precautions when sanding any paint:
u No children or pregnant women should enter the work
area where the paint sanding is being done until all
clean up is completed.
u A dust mask or respirator should be worn by all persons
entering the work area. The lter should be replaced
daily or whenever the wearer has difculty breathing.
Note: Only those dust masks suitable for working with lead
paint dust and fumes should be used. Ordinary painting
masks do not offer this protection. See your local hardware
dealer for the proper approved mask.
u NO EATING, DRINKING or SMOKING should be done
in the work area to prevent ingesting contaminated
paint particles. Workers should wash and clean up
BEFORE eating, drinking or smoking. Articles of food,
drink, or smoking should not be left in the work area
where dust would settle on them.
u Paint should be removed in such a manner as to
minimize the amount of dust generated.
u Areas where paint removal is occurring should be
sealed with plastic sheeting of 4 mils thickness.
u Sanding should be done in a manner to reduce tracking
of paint dust outside the work area.
u All surfaces in the work area should be vacuumed and
thoroughly cleaned daily for the duration of the sanding
project. Vacuum lter bags should be changed
frequently.
To Next Page
Loading...
