Black & Decker KA1000 - Page 8

8
Item Description
120 grit detailed nger sanding sheet.
For a medium nish for detailed sanding.
120 grit prole sanding sheet.
For a medium nish for prole sanding.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting sanding sheets (g. A & B)
u Detach the two additional diamond-shaped tips (10) from
the sanding sheet (11).
u Hold the tool with the sanding base facing upwards.
u Place the sanding sheet (11) onto the sanding base,
making sure that the holes in the sheet line up with the
holes in the base.
The diamond-shaped tip (10) can be reversed and replaced
when worn.
u When the front part of the tip is worn, detach it from the
sheet, reverse it and press it onto the sanding base again.
u When the whole tip is worn, remove it from the sanding
base and t a new tip.
u The polishing foam and pads (12) can be tted the same
way as the sanding sheets.
For optimal dust collection, ensure the correct type of sanding
paper is used.
Tip of the sanding base (g. C)
When the sanding base tip (5) or tip holder (4) is worn, it can
be reversed or replaced. Spare parts are available from your
Black & Decker dealer.
u Remove the screw (8).
u Reverse or replace the worn part.
u Fit and tighten the screw.
Finger attachment (g. D)
The nger attachment is used for ne detail sanding.
u Remove the screw (8).
u Remove the diamond-shaped tip holder (4) from the
sanding base.
u Fit the nger attachment (6) onto the sanding base.
u Fit and tighten the screw.
u Fit the appropriate sanding sheet onto the nger
attachment.
Prole attachment (g. E)
The prole attachment is used for contour sanding.
u Remove the screw (8).
u Remove the diamond-shaped tip holder (4) from the
sanding base.
u Fit the prole attachment (7) onto the sanding base.
u Fit and tighten the screw.
Fitting and removing a sanding prole (g. F1 & F2)
u Choose the sanding prole most suitable for your
application.
u Place one end of the sanding prole (9) into the recess at
the front end of the prole holder (7).
u Push the other end of the sanding prole until it clicks into
place.
u To remove the sanding prole, push it forward and pull the
rear end out of the prole holder (g. F2).
Fitting a sanding sheet onto a sanding prole (g. G)
u Align the sanding sheet with the sanding prole (9).
u Press the sanding sheet onto the sanding prole, making
sure that the sanding sheet follows the shape of the prole.
Fitting and removing the dust cassette (g. H)
u Slide the dust cassette (2) onto the tool and make sure
that it is securely located.
u To remove the dust casette, pull it to the rear and off the
tool.
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
u To switch the tool on, set the on/off switch (1) to position I.
u To switch the tool off, set the on/off switch to position O.
Emptying the dust cassette (g. H)
The dust cassette should be emptied every 10 minutes of use.
u While holding the tool, pull the dust cassette (2) to the rear
and off the tool.
u Remove the cassette door (13).
u Shake the door (13) and dust cassette (2) to empty the
contents.
u Ret the door (13) and dust cassette (2) onto the tool.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.