Need help?Do you have a question about the Black & Decker KW1200E and is the answer not in the manual?
Read all safety warnings, instructions, illustrations and specifications for safe operation.
Keep work area clean and well lit. Do not operate in explosive atmospheres.
Match plugs to outlets. Do not use adapter plugs with earthed tools.
Stay alert, watch what you are doing, use common sense, and wear PPE.
Do not force the tool. Ensure switch functions. Disconnect power for adjustments.
Have tool serviced by qualified personnel using identical replacement parts.
Hold by insulated surfaces. Cutter may contact cord. Beware of live wires.
Supervise children and persons with reduced capabilities. Keep them away from the work area.
Use approved, suitable, and undamaged extension cables.
Pictograms with date code shown on tool. Read manual, wear PPE.
Remove chip reflector, depress spindle lock, loosen collet, insert bit, tighten collet.
Fit bars to edge guide, insert into base, set distance, tighten screws.
Connect vacuum cleaner hose to the adaptor.
Fit template guide to base, insert screws from bottom, secure with nuts.
Fit distance piece to router base using provided screws.
Fit centring pin to workpiece side of bars, tighten with knob.
Fit edge guide, attach 'L' bar, adjust rotating attachment.
Set depth by distance X between depth stop bar and depth stop.
Loosen screw, pull lever, plunge bit to workpiece, push lever, set pointer to zero, add depth.
Place wood of desired depth between stops, tighten screw, fine adjust.
Adjust revolver depth stop for multiple cuts with different depths.
Set speed control knob to required speed. High for small bits, low for large bits.
Use straight-edged wood as batten to guide tool when edge guide is not suitable.
Secure template, ensure router bit extends below guide flange to cut shape.
Use for trimming wooden or laminate vertical projections.
Use to cut circular patterns. Drill hole for pin, place router, adjust radius.
Helps maintain cutting distance on irregularly shaped pieces. Adjust edge guide wheel.
Press On/Off switch while holding lock-off button to switch on.
Work edges counter/clockwise. Use HSS for softwood, TCT for hardwood. Use without guide for creative work.
Tools lubricated at factory. Lubricate annually or more often if used heavily.
Clean ventilation slots with brush. Use mild soap and damp cloth. Do not use solvents.
Use only BLACK+DECKER accessories for safety and performance.
Read all safety warnings, instructions, illustrations and specifications for safe operation.
Keep work area clean and well lit. Do not operate in explosive atmospheres.
Match plugs to outlets. Do not use adapter plugs with earthed tools.
Stay alert, watch what you are doing, use common sense, and wear PPE.
Do not force the tool. Ensure switch functions. Disconnect power for adjustments.
Have tool serviced by qualified personnel using identical replacement parts.
Hold by insulated surfaces. Cutter may contact cord. Beware of live wires.
Supervise children and persons with reduced capabilities. Keep them away from the work area.
Use approved, suitable, and undamaged extension cables.
Pictograms with date code shown on tool. Read manual, wear PPE.
Remove chip reflector, depress spindle lock, loosen collet, insert bit, tighten collet.
Fit bars to edge guide, insert into base, set distance, tighten screws.
Connect vacuum cleaner hose to the adaptor.
Fit template guide to base, insert screws from bottom, secure with nuts.
Fit distance piece to router base using provided screws.
Fit centring pin to workpiece side of bars, tighten with knob.
Fit edge guide, attach 'L' bar, adjust rotating attachment.
Set depth by distance X between depth stop bar and depth stop.
Loosen screw, pull lever, plunge bit to workpiece, push lever, set pointer to zero, add depth.
Place wood of desired depth between stops, tighten screw, fine adjust.
Adjust revolver depth stop for multiple cuts with different depths.
Set speed control knob to required speed. High for small bits, low for large bits.
Use straight-edged wood as batten to guide tool when edge guide is not suitable.
Secure template, ensure router bit extends below guide flange to cut shape.
Use for trimming wooden or laminate vertical projections.
Use to cut circular patterns. Drill hole for pin, place router, adjust radius.
Helps maintain cutting distance on irregularly shaped pieces. Adjust edge guide wheel.
Press On/Off switch while holding lock-off button to switch on.
Work edges counter/clockwise. Use HSS for softwood, TCT for hardwood. Use without guide for creative work.
Tools lubricated at factory. Lubricate annually or more often if used heavily.
Clean ventilation slots with brush. Use mild soap and damp cloth. Do not use solvents.
Use only BLACK+DECKER accessories for safety and performance.
General| Toolholder | 6.35 (1/4\ |
|---|---|
| Input power | 1200 W |
| Product color | Black, Orange |
| Speed preselection | Yes |
To Next Page