BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALUSING YOUR BLACKSTONE
CONNECT THE LPG CYLINDER
ONLY USE A 1 LB (453 G) CYLINDER
LPG CYLINDER SAFETY
• The LPG supply cylinder to be used must be constructed and
marked in accordance with the specifications for LP gas cylin-
ders, U.S. Department of Transportation (DOT) or the Standard for
Cylinders, Spheres and Tubes for the Transportation of Dangerous
Goods, CAN/CSA-B339.
• Only LPG cylinders marked “propane” shall be used.
• The cylinder used, if in excess of 2.2 Ib (1.00 kg) propane capacity,
must include a collar to protect the cylinder valve.
• The LPG cylinder supply system must be arranged for vapor
withdrawal.
Always keep new LPG cylinders in upright position during use, transit or
Always keep new LPG cylinders in upright position during use, transit or
storage.
LEAK TEST INSTRUCTIONS
STEP 01
Turn the control knobs to OFF.
STEP 02
Connect the LPG cylinder to the regulator. Connect the
regulator to the appliance.
STEP 03
Use a clean paintbrush
to brush a mild soap and
water solution onto joint areas of
valves and regulator.
Leaks are indicated by growing
Leaks are indicated by growing
bubbles.
DISCONNECTING THE LPG CYLINDER
1 LB (453 G)
STEP 01
Ensure that the control knob(s) are turned to OFF.
STEP 02
Once the appliance has cooled, disconnect the regulator
from the gas line by unscrewing the collar.
STEP 03
Unscrew the LPG cylinder from the regulator.
STEP 04
Place dust cap on LPG cylinder valve outlet whenever
cylinder is not in use.
Only install the type of dust cap on cylinder valve outlet that is provided
Only install the type of dust cap on cylinder valve outlet that is provided
with the cylinder valve. Other types of caps or plugs may result in leakage of
with the cylinder valve. Other types of caps or plugs may result in leakage of
propane.
STORING LPG CYLINDERS
WARNING
• DO NOT store a spare LPG cylinder under, near, or in this
appliance.
• DO NOT fill an LPG cylinder beyond 80% full.
If the information above is not followed exactly, a fire causing
death or serious injury may occur.
• The LPG cylinder must be disconnected when the appliance is
not in use.
• Only store the appliance indoors if the LPG cylinder is disconnected
and removed from the appliance.
STEP 01
Screw in the LPG
cylinder into the gas regulator,
turning the cylinder clockwise.
The regulator may make a humming
The regulator may make a humming
or whistling noise during operation.
or whistling noise during operation.
This will not aect safety or use of the
This will not aect safety or use of the
appliance.
STEP 02
Insert the regulator and LPG cylinder into the gas line of the
appliance. Turn the collar of the regulator clockwise to secure it to
the gas line.
STEP 04
If growing bubbles appear, re-tighten connections.
WARNING
If leaks cannot be stopped, DO NOT try to repair.
Regulator must be replaced with a Blackstone approved
model by a professionally licensed, authorized dealer.
REGULATOR SAFETY
• Use this appliance, as purchased, only with gas and regulator/
valve assembly supplied. DO NOT use quick connect fittings or
other add-ons.
• DO NOT cross thread (force at an improper angle) the connection
between your LPG cylinder and regulator.
• If you can not connect the regulator, DO NOT use the regulator.
Regulator must be replaced with a Blackstone approved model by a profession-
Regulator must be replaced with a Blackstone approved model by a profession-
ally licensed, authorized dealer.
ally licensed, authorized dealer.
Ensure that the LPG cylinder is
positioned below the regulator.
(If the liquid level of the propane is
(If the liquid level of the propane is
above the regulator, the regulator will
above the regulator, the regulator will
frost.)
IF FROSTING PERSISTS
AFTER CYLINDER IS ANGLED
CORRECTLY:
STEP 01
Turn o the appliance
and disconnect LPG cylinder
immediately. This indicates a
problem with the LPG cylinder
and it should not be used on
any product.
STEP 02
Return LPG cylinder to
supplier.
MODELS: 2321 • 2321CA
To Next Page
Loading...
