Blaupunkt Blue Magic XLf 200 A - Page 6

Evo
jos
nekoliko vaznih
objasnjenja:
Okretanjem
regulatora
u smjeru kazaljke
na
satu povecava
se
osjetljivost
ulaza pojacala
a
time
i jacina zvuka. Pritom nije
samo
rijec
o regulaciji jacine zvuka; u krajnjem
polozaju
se
ne maze postiCi veci
ucinak pojacala,
cak
iako
se
to
taka
cuje.
Sustav
same
brze povecava jacinu zvuka kada
se
regulacija
jacine zvuka autoradija okrene
do
kraja.
CROSSOVER
reguliranje frekvencije
CROSSOVER
reguliranje
(
~
)
omogucuje podesavanje zeljene
ulazne
frekvencije.
Primjer:
Kod postavke od 150Hz
pojacalo ima frekvencijsko podrucje
od
20
Hz
do
150
Hz.
Postavke
Kao
osnovne postavke prije stavljanja u pogon preporucu-
jemo
sljedece polozaje
regulate~~:
Osjetljivost
(VOL)
pol.
na
minimum, faza
(PHASE)
pol.
(
~
)
na
0°,
filtar
(CROSSOVER)
pol.
(
5::
na
ca.
80
Hz.
Ukljucite
uredaj i odaberite glazbeni
komad s izrazenom reprodukcijom
basa.
Pojacajte glasnocu
na Vasem
stereo uredaju
do
zelje~~
razine glasnoce zvuka.
Zatim
regulator
osjetljivosti
~
-
~
_)
oprezno okrecite dok ne zacujete jasno pojacavanje razine
basa.
Zatim
regulatorom filtra
(
~
)
odaberite postavku filtra,
kojom
se
postize
do
bar kontinuirani
bas.
Mazda cete
mor~!
_
i
naizmjence optimirati postavku regulatora osjetljivosti
(
_
~
)
i postavku filtra
CD.
Brujeci bass
prenaglasenim
volumenom zahtijeva postavku
filtra s
nizom
frekvencijom.
Fazni
regulator
(
~
)
valja
podesiti taka da
se
bas
sto
bolje
integrira u
sliku
zvuka
ida
sene
cuje
kao samostalni izvor.
Svoje postavke
Xlf
200
A
provjeravajte
is
do
kraja okrenutim
regulatorom
basa
te eventual no
ukljucenom
Lou~~ess
(gla-
snocom).
Prejako
pojacavanje subwoofera
(paz.
(
_
~
)
)
dovodi
do
isprekidane reprodukcije i
maze
unistiti zvucnik.
Prikaz
radnog
stanja
(PRT
/PWR)
Zeleno
svjetlo:
Krajnji stupanj, regularni prikaz radnog stanja.
Crveno
svjetlo:
Krajnji stupanj
je
elektronski iskljucen, buduci
da
postoji
pogreska.
Recikliranje i
zbrinjavanje
~
Molimo
Vas
da
za
zbrinjavanja proizvoda koristite
A
sustave vracanja i skupljanja koji vam stoje
na
ras-
- polaganju.
Promjene pridrzane!
XLf200A
USA
Please
read
these operating instructions before
using
the equipment for the first time.
Safety
Notes
Please
observe
the
following
safety notes during
the
installation
and connection.
-
Disconnect
the negative
terminal
of the battery before
carrying out
installation
and
connection
work.
-
Observe
the
vehicle
manufacturer's
safety
instructions
(regarding airbags,
alarm
systems,
trip computers,
vehicle immobilisers}.
- When you
drill
holes, ensure
that
you
do
not damage any
vehicle components.
- If
the positive and negative
cable
are extended, ensure
that
the cross section
is
not
less
than
2.5
mm
2
•
-
An
incorrect installation
can
result in malfunctions
of
the
electronic
vehicle
systems or your car sound system.
Installation and connection instructions
With respect
to
accident safety,
the
XLf
200
A must be
se-
cured in a professional way.
When selecting
the
installation location,
select
a dry
loca-
tion
that
offers
sufficient
air circulation
for
cooling
the
amplifier.
The
Xlf
2000
A
must
not
be
installed
on rear shelves, rear
seats
or other locations that are open
to
the front.
The installation location must be
suitable
to
accept
the
accompanying screws and
provide
a
firm
support
(see
page
37
I
Fig.
1
).
The amplifier power
cable
must be fitted with a fuse no more
than
30
em
from the battery
to
protect the
vehicle
battery in
case
of
a short circuit between power amplifier and battery.
The fuse
of
the amplifier
protects
only
the
amplifier,
not
the
vehicle battery.
Connection
(see
page
38/
Fig.
2)
10
A
fuse
(2)
Preamplifier
inputs
Power-on indicator
(Protect/Power)
(
~
~)
Input
sensitivity
Upper
cut-off
frequency
Phase
position
Connector
cable
(§)
Right loudspeaker
input
(
~
)
Left loudspeaker
input
-Earth
(
~~1
)
+
Battery
I
35