EasyManua.ls Logo

Bliss Tubs B2645 - User Manual

Bliss Tubs B2645
40 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Walk-in Bathtub
Installation Manual
QUESTIONS?
Please call your dealer rst:
Telephone:
MODELS
B2645 B2651 B2653
B2848 B2851 B2948
B3048 B3052 B3054
B3150 B3153
B3060 B3260
B3052HC B3252HC
B3355 B3555 B3237
B305546 B315546 B306022
SAVE THESE INSTRUCTIONS
Image shown is a dual system tub. This manual also covers Bliss Walk-in
Tubs with air or water jets only, or without jets.
© 2015 - 2017 Bliss Walk-in Bathtubs. All Rights Reserved.

Table of Contents

Questions and Answers

  • P
    Paul BlakeAug 18, 2025
    Why is my Bliss Tubs Hot Tub door leaking?
    • R
      Randall CarlsonAug 18, 2025
      A Bliss Tubs Hot Tub door might leak due to several reasons: * The door handle may not be completely shut. Ensure it's fully engaged. * The door seal or jamb could be dirty. Try wiping them clean. * The door seal might be ripped, torn, or damaged, requiring replacement. * The tub might not be level or plumb. Make sure it is level front to back and side to side. * All six feet may not be touching the ground. Ensure all six feet are on the ground and secure. * The door may not be sealing or shut tight enough. Look for daylight through the seal and try tightening the handle.
  • S
    Steven OliverAug 20, 2025
    How to fix weak handspray flow in Bliss Tubs B2645 Hot Tub?
    • A
      Amanda BellAug 20, 2025
      A weak or non-existent handspray flow in your Bliss Tubs Hot Tub can be caused by several issues: * A clog at the handspray. Remove the handspray and clear any debris. * A clog in the diverter. Clean out the stem and diverter body. * The backflow preventer being in the wrong location. Ensure it's correctly placed: Bellevue (next to handspray); Montage (near diverter). * Low pressure in the house. Make sure the main shut-off is completely open. * The wall shut-off valves not being fully open. Open the wall supply valves completely.
  • F
    fedwardsAug 23, 2025
    What to do if there is no flow from my Bliss Tubs B2645 Hot Tub spout or handspray?
    • T
      Todd MccarthyAug 23, 2025
      If there's no flow from the spout or handspray of your Bliss Tubs Hot Tub, check the following: * Ensure the wall supply valves are open. * The diverter might have a plastic half-moon flow diverter installed backward. Take apart the diverter stem and reposition the part.
  • C
    Caitlin FordAug 26, 2025
    Why is the water not completely diverting in my Bliss Tubs Hot Tub?
    • K
      kennethtrujilloAug 26, 2025
      If the water is not completely diverting in your Bliss Tubs Hot Tub, consider these possible causes: * The handle may not be completely turned. Test the diverter handle in its full left-to-right range of motion. * The trim handle may not be properly installed. Check the handle position to allow for a full 180º range of motion. * The diverter stem may be clogged. Remove the stem and clean the diverter body.
  • D
    David HartAug 27, 2025
    How to stop water leaking from the handspray connection on my Bliss Tubs B2645 Hot Tub?
    • A
      andreaguerraAug 28, 2025
      If water is leaking from the handspray connection of your Bliss Tubs Hot Tub, check these: * A missing gasket between the hose and handspray. Install a gasket and retest. * Teflon tape not used on the threads. Install Teflon tape on the threads and retest. * A fine crack in the plastic threads on the handspray. Consider replacing the handspray.
  • A
    Amanda WhiteheadAug 30, 2025
    What causes a water leak near the diverter on my Bliss Tubs B2645 deck?
    • K
      Kevin RobertsonAug 30, 2025
      A water leak near the diverter on your Bliss Tubs Hot Tub deck could be because the stem is not tightened enough in the diverter. Tighten the diverter stem to the diverter body.
  • J
    Jessica CampbellSep 2, 2025
    Why is there a water leak near the valve on my Bliss Tubs B2645 deck?
    • N
      Nicholas FrankSep 2, 2025
      A water leak near the valve on your Bliss Tubs Hot Tub deck may be due to the hot/cold cartridge not being tight enough in the valve body. Tighten the cartridge in the valve body.
  • M
    Matthew CarneySep 4, 2025
    Why does the diverter valve trim spin on my Bliss Tubs B2645?
    • C
      Carol MorganSep 4, 2025
      If the diverter valve trim spins on your Bliss Tubs Hot Tub, it could be due to: * A broken stem/shaft. Replace the stem/shaft. * Locking nuts not adequately tightened. Remove the trim and tighten the locking nuts.
  • J
    Joseph HartmanSep 7, 2025
    What to do if water is leaking from the handspray flex hose on my Bliss Tubs B2645?
    • A
      Arthur WangSep 7, 2025
      If water is leaking from the handspray flex hose on your Bliss Tubs Hot Tub, it could be that the flex hose is damaged inside. Replace the flex hose.
  • J
    Jeffrey EllisonSep 9, 2025
    Why does the hot/cold valve or spout trim turn more than 90º on my Bliss Tubs Hot Tub?
    • G
      Gary RodriguezSep 9, 2025
      If the hot/cold valve or spout trim on your Bliss Tubs Hot Tub turns more than 90º, the locking nuts may not be adequately tightened. Remove the trim and tighten the locking nuts.

Bliss Tubs B2645 Specifications

General IconGeneral
BrandBliss Tubs
ModelB2645
CategoryHot Tub
LanguageEnglish