How to stop my Blomberg WNF 5200 Washer from vibrating and making noise?
T
Tonya ChavezAug 20, 2025
If your Blomberg Washer is vibrating or making noise, several factors could be the cause. First, ensure the machine is standing balanced by adjusting the feet. A hard substance might have entered the pump filter, so clean the pump filter. Check that the transportation safety bolts are removed. Also, the laundry quantity might be too little or too much; add more laundry or take some out to balance the load. Finally, make sure the machine isn't leaning on anything.
J
Justin DavisAug 22, 2025
What to do if my Blomberg WNF 5200 Washer does not drain water?
J
James WhitneyAug 22, 2025
If your Blomberg Washer isn't draining water, the water drain hose might be clogged or twisted, so clean or flatten the hose. Alternatively, the pump filter might be clogged; in this case, clean the pump filter.
L
lsantiagoAug 25, 2025
How to open the loading door of my Blomberg WNF 5200 Washer?
E
Eddie TaylorAug 25, 2025
If the loading door of your Blomberg Washer cannot be opened, it could be due to a few reasons. The door lock may be activated because of the water level in the machine; drain the water by running the Pump or Spin programme. The machine might be heating up the water or it is at the spinning cycle; wait until the programme completes. Alternatively, the child lock may be engaged; wait a couple of minutes for deactivation of the door lock.
M
Matthew WalterAug 26, 2025
Why doesn't my Blomberg Washer switch to the spinning step?
E
Emily WilsonAug 27, 2025
If your Blomberg Washer isn't switching to the spinning step, there might be an unbalanced load in the machine. The automatic unbalanced load detection system may be activated due to the laundry's distribution in the drum. Also, the machine will not spin if water is not drained completely; check the filter and the draining hose. Excessive foam from too much detergent usage can also prevent spinning; use the recommended amount of detergent.
T
Teresa PerezAug 28, 2025
Why my Blomberg WNF 5200 doesn't fill with water?
I
imcdonaldAug 28, 2025
If your Blomberg Washer isn't filling with water, it could be due to several reasons. Ensure the tap is turned on. Check if the water inlet hose is bent and flatten it if necessary. The water inlet filter might be clogged, so clean it. Also, make sure the loading door is closed.
M
Maria EllisonAug 30, 2025
Why is my Blomberg WNF 5200 Washer leaking water from the bottom?
R
Richard SandersAug 30, 2025
If you notice water leaking from the bottom of your Blomberg washing machine, it could be due to a clogged or twisted water drain hose. Clean or flatten the hose to resolve this. Another possibility is a clogged pump filter, which would also need to be cleaned.
K
Kerry DixonSep 1, 2025
What to do if a Blomberg WNF 5200 programme cannot be started or selected?
C
Carol MartinSep 1, 2025
If a programme cannot be started or selected on your Blomberg Washer, the machine may have switched to self-protection mode due to a supply problem, such as line voltage or water pressure issues. Press and hold the Start / Pause / Cancel button for 3 seconds to reset the machine to factory settings.
J
John TurnerSep 3, 2025
Why does washing take longer than specified in the Blomberg Washer manual?
S
Suzanne CareySep 3, 2025
Several factors can cause your Blomberg Washer to take longer than usual. Low water pressure can cause the machine to wait until it has enough water, extending the wash time. Low voltage can also prolong washing to avoid poor results. A low input water temperature will extend the time needed to heat the water. The machine may increase the amount of rinse water or add an extra rinsing step if necessary. Excessive foam from too much detergent can also activate the automatic foam absorption system, lengthening the wash cycle. Use recommended amount of detergent.
L
ltrujilloSep 5, 2025
Why is there too much foam in my Blomberg Washer?
J
Jeffrey BarnesSep 5, 2025
Excessive foam in your Blomberg Washer can occur for several reasons. You might be using detergents not designed for washing machines, so switch to appropriate detergents. Using too much detergent is another common cause; use only a sufficient amount. Improperly stored detergent can also contribute; store detergent in a closed, dry location away from excessive heat. Some meshed laundry, like tulle, may create too much foam due to their texture; use less detergent for these items. Ensure you're putting the detergent in the correct compartment. If the softener is being taken early, there may be a problem in the valves or in the detergent dispenser.
S
Stephanie CastanedaSep 7, 2025
Why does my Blomberg WNF 5200 leave stains or not whiten laundry?
S
Stephanie SimsSep 7, 2025
If your Blomberg Washer isn't effectively removing stains or whitening laundry, it could be due to several reasons. You might not be using enough detergent, so use the recommended amount appropriate for water hardness and the laundry. Overloading the machine can also hinder performance, so load with amounts recommended in the Programme and consumption table. Ensure you've selected the proper programme and temperature for the laundry. Using the wrong type of detergent can also be a factor, so use original detergent appropriate for the machine. Additionally, make sure you're putting the detergent in the correct compartment and not mixing the bleaching agent and the detergent with each other.
To Next Page
General
