Blower Engineering Tri-Lobe TL Series

Questions and Answers

M
Matthew ClayAug 7, 2025
What to do if the power absorbed is different from the rated value in Blower Engineering Industrial Equipment?
- A
  Andrea LopezAug 7, 2025
  If the power absorbed by your Blower Engineering Industrial Equipment differs from the rated value, there are several potential causes. First, check if the differential pressure deviates from the rated value and reset it if necessary. Also, verify that the rotation speed matches the rated value and adjust it accordingly. An incorrect electrical connection could also be the culprit, so inspect the electrical system. Finally, stop the blower immediately if the rotors are making contact.
K
Krystal FullerAug 11, 2025
What to do if the outlet temperature is different from the rated value in Blower Engineering Tri-Lobe TL?
- A
  Andrea HollandAug 12, 2025
  If the outlet temperature of your Blower Engineering Industrial Equipment differs from the rated value, immediately stop the blower. Then, check if the inlet temperature matches the design value and reset if needed. Also, ensure the compression ratio aligns with the rated values by checking inlet and outlet pressures and adjusting to design conditions. Finally, worn rotors can cause this issue, so measure the rotor clearances to assess their condition.
S
Sara GomezAug 15, 2025
How to troubleshoot unusual noises and/or vibrations in Blower Engineering Tri-Lobe TL Industrial Equipment?
- B
  bthomasAug 16, 2025
  If you notice unusual noises or vibrations in your Blower Engineering Industrial Equipment, stop the blower immediately. Check if the differential pressure exceeds the rated value and reset the inlet and outlet pressures if needed. Also, measure gear and rotor clearances to check for rotors making contact. Clean the rotors and compression chamber thoroughly to remove any scale on internal parts. Measure the bearing clearances and replace them if they are worn. Remove any foreign particles and clean the inside of the blower.
R
Ronald AndersonAug 21, 2025
Why is the inlet pressure different from the design value in Blower Engineering Industrial Equipment?
- S
  smithchristopherAug 21, 2025
  If the inlet pressure of your Blower Engineering Industrial Equipment differs from the design value, it could be due to a clogged inlet piping. Check the piping and remove any obstructions. Another possible cause is that the rotation speed is not the same as the design RPM. Check the rotation speed and reset it to the design RPM.
C
Christopher McdonaldAug 25, 2025
Why is the outlet pressure different from the rated value in Blower Engineering Industrial Equipment?
- D
  Dawn ClarkAug 25, 2025
  If the outlet pressure of your Blower Engineering Industrial Equipment differs from the rated value, it may be due to a clogged outlet piping. Check the piping and remove any obstructions. Alternatively, the rotation speed might not be the design RPM. Check the rotation speed and reset it to the design RPM.
C
Charles TurnerAug 28, 2025
What causes high oil temperature in Blower Engineering Tri-Lobe TL Industrial Equipment?
- E
  Elizabeth DukeAug 28, 2025
  If your Blower Engineering Industrial Equipment is experiencing high oil temperature, consider these potential causes. First, check if the oil level is too high and reset it to the correct level. The oil may also be too viscous, in which case you should use a less viscous oil. If the differential pressure is high, consult paragraph 7.2. Finally, if the oil produces foam, change the type of oil used.
S
Sabrina KelleySep 2, 2025
How to fix oil loss in Blower Engineering Tri-Lobe TL?
- E
  Erika AllenSep 2, 2025
  If your Blower Engineering Industrial Equipment is experiencing a loss of oil, it could be due to several reasons. The drive shaft seal may be worn, requiring replacement. Alternatively, the oil drain and level plugs gaskets might be worn, in which case you should replace the gaskets. Finally, broken oil level sight glasses can cause oil loss; replace the sight glasses and refill with oil.

Blower Engineering Tri-Lobe TL Series Specifications

General

Series	TL Series
Application	Pneumatic Conveying, Wastewater Treatment, Vacuum Systems
Pressure	Up to 15 PSI
Construction	Cast iron housing with steel rotors
Mounting	Horizontal
Lubrication	Oil Lubricated

Blower Engineering Tri-Lobe TL Series - User Manual

Table of Contents

Questions and Answers

Blower Engineering Tri-Lobe TL Series Specifications