Blue Angel 50TK User Manual

GENERAL SAFETY INFORMATION
CALIFORNIA PROPOSITION 65
This product or its power cord contains
chemicals, including lead, known to the State of
California to cause cancer and birth defects or other reproductive harm.
Wear gloves when handling this product, and wash hands after handling.
GENERAL SAFETY
Do not submerge motor or allow motor to be
exposed to water. Personal injury and/or death
WILL result.
Do NOT use to pump flammable or explosive fluids such as
gasoline, fuel oil, kerosene, etc. Do NOT use in a flammable
and/or explosive atmosphere. Pump SHOULD only be used to
pump clear water. Personal injury and/or death WILL result.
Risk of electrical shock. ALL wiring must be
performed by a qualified electrician.
Do NOT walk on wet areas until ALL power is turned off.
Failure to follow this warning WILL result in fatal electrical
shock.
1. Read all instructions before operation.
2. Disconnect power and release all pressure within
the system before servicing any component.
3. Drain all liquids from system before servicing.
Secure the discharge line before starting the
pump. An unsecured discharge line MAY whip.
Personal injury and/or property damage COULD result.
4. Periodically inspect pump and system components, checking
for weak and/or worn hoses. Insure all connections are secure.
50TK
Portable Utility Pump
OPERATING INSTRUCTIONS & PARTS MANUAL
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL - DO NOT DISCARD.
Failure to follow these instructions could result in property damage, serious injury or death.
For parts, product & service information visit www.blueangelpumps.com
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2016, Blue Angel Pumps, Harrison, Ohio.
DESCRIPTION
This self-priming portable utility pump is designed to be used as
a transfer pump for such applications as emptying water heaters,
livestock tanks, etc. Pump can also be used for an intermittent
pressure boost for applications such as washing cars, cleaning
driveways, etc. The motor is air cooled; it is not designed to operate
under water.
NOTE: This pump is not intended for permanent installation or long,
extended periods of continuous operation.
UNPACKING
After unpacking the utility pump, carefully inspect for any damage
that may have occurred during transit. Check for loose, missing or
damaged parts. If you need assistance, call our Customer Service
Department at 1-888-636-6628.
SAFETY GUIDELINES
To help recognize this information, observe the following signal
words/hazard classifications.
Danger indicates an imminently hazardous
situation which, if not avoided, WILL result in
death or serious injury.
Warning indicates a potentially hazardous
situation which, if not avoided, COULD result in
death or serious injury.
Caution indicates a potentially hazardous
situation which, if not avoided, MAY result in
minor or moderate injury.
Notice indicates important information, that if
not followed, may cause damage to equipment.
This is the safety alert symbol. It is used to alert you to potential bodily
injury hazards. Obey all safety messages that follow this symbol to avoid
possible harm.
NOTE: Information that requires special attention.
Specications
Motor
Single Phase - 115V, 60 Hz, 8,000 RPM
Horsepower
1/2 HP
Motor
Series Wound (brush type) AC/DC Operation
Inlet/Outlet Openings
3/4 inch NPT
Impeller
Thermoplastic
Pump Housing
Cast iron
Motor Housing
Cast iron
Motor Shaft
Cold rolled steel
Shaft and Volute
Seal
Buna-N
Motor Bearings
Permanently lubricated
Rolling element bearings
Maximum Fluid
Temperature
120°F
321301-026 3/16
®

Blue Angel 50TK Specifications

General

Brand	Blue Angel
Model	50TK
Category	Water Pump
Language	English

Summary

Product Description and Unpacking

Product Description

Details the self-priming portable utility pump's intended uses and limitations.

Unpacking Instructions

Guidance on inspecting the pump for damage or missing parts after delivery.

Safety Information

Hazard Identification and Warnings

Explains signal words (DANGER, WARNING, CAUTION, NOTICE) and specific warnings like Prop 65.

General Operational Safety

Rules for safe operation, including submersion, flammable fluids, wiring, and wet areas.

Pre-Operation Safety Steps

Essential steps before operation: read instructions, disconnect power, drain, secure discharge line.

Specifications

General Safety Information Continued

Thermal Protector and Cord Safety

Information on automatic motor restart and protecting electrical cords from damage.

Pressure Relief and Hose Inspection

Requirements for pressure relief and periodic inspection of hoses and connections.

Installation Instructions

Electrical Safety During Installation

Mandates disconnecting power and using GFCI outlets and proper grounding.

Voltage and Extension Cord Usage

Specifies voltage requirements and guidelines for using extension cords.

Pump Placement and Suction Line Setup

Guidance on pump location, suction lift limits, and using strainers.

Pump Operation

Priming and Filling

Instructions for filling the pump with water before operation to prevent seal damage.

Connecting Power and Starting

Steps for plugging into GFCI outlets, starting the pump, and pressure boosting.

Power Cord Safety

Warning against cutting the grounding prong to avoid fatal shock and voiding warranty.

Maintenance Procedures

Cooling and Electrical Disconnection

Emphasizes allowing the pump to cool and disconnecting power before servicing.

Brush Inspection and Replacement

Guidelines for inspecting brushes after 100 hours and replacing them.

Additional Repair Steps

Detailed instructions for replacing bearings, shaft seals, and gaskets.

Troubleshooting Chart

Pump Will Not Start or Run

Lists possible causes like blown fuse, low voltage, blocked impeller, or defective motor.

Pump Will Not Prime

Identifies causes such as air leaks, blocked impeller, worn seal, or high suction lift.

Flow Rate Issues and Seal Leaks

Addresses low flow rate due to fouled piping or voltage, and seal leaks from worn seals or damage.

Thermal Protector Tripping

Explains causes like binding, high temperature, low voltage, or blocked air vents.

Replacement Parts and Assistance

Contact Information for Support

Provides contact details for replacement parts or technical assistance.

Replacement Parts List

Lists available replacement parts, including brush kits and impeller/seal kits.

Limited Warranty Information

Warranty Coverage and Exclusions

Details the one-year warranty, covered defects, and excluded causes like misuse or neglect.

Limitation of Liability

States limitations on implied warranties and excludes liability for consequential damages.

Warranty Claim Procedure

Instructs users to retain proof of purchase and contact for return authorization.