FOR POSITIONING ONLY (FPO)
MAC ADDRESS LABEL
(2.4 in. x 0.85 in.)
(FPO) ATE CODE
SERIAL NUMBER LABEL
(1.6 in. x 0.6 in.)
MODEL NO:
BB-ZB1
RATING: 5VDC, 500mA
FCC ID: LDV-BBZIGBEE
This device complies with part 15 FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference. (2) This device
must accept any interference received including interference
that may cause undesired operation.
NO USER SERVICEABLE PARTS
INSIDE. RETURN TO PANAMAX
IF SERVICE IS REQUIRED.
USE ONLY INDOORS.
Designed in USA
Made in China
PANAMAX LLC, PETALUMA, CA
(800) 472-5555
www.mybluebolt.com, www.panamax.com
NET.
ZIGBEE
BB-ZB1
Quick Start Guide
NETWORK
5VDC
500mA
RESET / RESTORE
NETWORK
5VDC
500mA
RESET / RESTORE
www.panamax.com
www.mybluebolt.com www.furmansound.com
NET.
ZIGBEE
1. BB-ZB1
2. Vertical Mount Stand
3. Power Cord & Transformer
4. LAN Cable - CAT5E
Package Includes:
ATTENTION: PLEASE RETAIN MAC ADDRESS
IDENTIFICATION NUMBER AND CHALLENGE KEY,
WHICH APPEARS ON THE BACK PANEL OF THE
BB-ZB1. This is unique to every BB-ZB1 unit and
will be required for registration.
It is recommended that you read the entire list of
instructions before proceeding.
Installation:
• BB-ZB1 must be located in a relatively open area so
that radio signal is not blocked.
• Unit may be mounted at or vertically using the sup-
plied stand. Can also be wall mounted or equipment
rack mounted using keyhole slots on back of product.
• Connect power cord to BB-ZB1 and wall outlet.
• Connect LAN Cable from router to BB-ZB1.
NETWORK
5VDC
500mA
Router
NETWORK
• RED LED: No network
established.
See troubleshooting.
AC Power
LAN Cable
• Flashing Green LED:
Indicates mode to allow
an end-user device to
join the network.
Ethernet indicators:
NETWORK
5VDC
500mA
RESET / RESTORE
Reset Button for System Reset:
• If the reset button is pressed for less than 8
seconds, the system goes to startup mode.
• If thereset button is pressed for more than 8
seconds, the system restores all factory settings
and goes to startup mode.
Online Registration:
Your BlueBOLT™ enabled Power Management
Component is completely plug-and-play and does
not require any software installation. The BlueBOLT™
control interface is operated through your web
browser.
1) Using any Internet connected computer, go to www.
mybluebolt.com using your standard Internet browser.
2) Follow the on screen instructions to create an
account and/or take control of your BlueBOLT™
enabled product. Note: you will need the BlueBOLT-
BB-ZB1’s unique MAC address and challenge key
(provided on the card’s protective packaging as well
as on the label of the card itself) in order to register
the unit online.
• ACTIVITY:
Data Activity
on Ethernet
Connection
• LINK:
Valid Ethernet
Connection
NET.
Network Indicator:
Indicates status of Internet connection.
• BLUE LED: Connection
to network and BlueBOLT
established.
• GREEN LED: Connection
to network established, but
connection to BlueBOLT not
established. See trouble-
shooting guide.
ZIGBEE
NET.
NET.
Zigbee
®
indicator:
Indicates status of ZigBee
®
network.
• LED is Off: Not joined
to any ZigBee network.
• Green LED: ZigBee
Active
ZIGBEE
ZIGBEE
DQS-00014-B 11/12
To Next Page
Need help?
General