205 S450 Operation & Maintenance Manual
DIAGNOSTIC SERVICE CODES (CONT'D)
Service Codes List (Cont’d)
CODE DESCRIPTION CODE DESCRIPTION
H7404 Main controller no communication M0822 Engine coolant temperature out of range low
M0826 Engine coolant temperature pre-shutdown
L0102 Lights button error ON M0909 Fuel level too low
L0202
High-flow enable / auto idle enable button error
ON
M0921 Fuel level out of range high
L0302 Auxiliary enable button error ON M0922 Fuel level out of range low
L0402 Information button error ON M1016 Hydraulic charge filter not connected
L7404 Main controller no communication M1017 Hydraulic charge filter plugged
L7672 Left display panel needs programming M1121 Seat bar sensor out of range high
M1122 Seat bar sensor out of range low
M0116 Air filter not connected M1128 Seat bar sensor failure
M0117 Air filter plugged M1305 Fuel hold solenoid short to battery
M0216 Hydraulic / Hydrostatic filter not connected M1306 Fuel hold solenoid short to earth
M0217 Hydraulic / Hydrostatic filter plugged M1307 Fuel hold solenoid open circuit
M0309 System voltage too low M1402 Fuel pull solenoid error ON
M0310 System voltage too high M1403 Fuel pull solenoid error OFF
M0311 System voltage extremely high M1407 Fuel pull solenoid open circuit
M0314 System voltage extremely low M1428 Fuel pull solenoid failure
M0322 System voltage out of range low M1502 Traction lock pull output error ON
M0409 Engine oil pressure too low M1503 Traction lock pull output error OFF
M0414 Engine oil pressure extremely low M1507 Traction lock pull output open circuit
M0415 Engine oil pressure in shutdown M1528 Traction lock pull output failure
M0421 Engine oil pressure out of range high M1605 Traction lock hold solenoid short to battery
M0422 Engine oil pressure out of range low M1606 Traction lock hold solenoid short to earth
M0509 Hydraulic charge pressure too low M1607 Traction lock hold solenoid open circuit
M0510 Hydraulic charge pressure too high M1705 Hydraulic lock valve short to battery
M0511 Hydraulic charge pressure extremely high M1706 Hydraulic lock valve short to earth
M0514 Hydraulic charge pressure extremely low M1707 Hydraulic lock valve open circuit
M0515 Hydraulic charge pressure in shutdown M1732 Hydraulic lock valve overcurrent
M0521 Hydraulic charge pressure out of range high M1805 Lift spool lock output short to battery
M0522 Hydraulic charge pressure out of range low M1806 Lift spool lock output short to earth
M0610 Engine speed too high M1807 Lift spool lock output open circuit
M0611 Engine speed extremely high M1832 Lift spool lock output overcurrent
M0613 Engine speed no signal M2005 Two-speed primary solenoid short to battery
M0615 Engine speed in shutdown M2006 Two-speed primary solenoid short to earth
M0618 Engine speed out of range M2007 Two-speed primary solenoid open circuit
M0634 Engine speed invalid information from ECU M2032 Two-speed primary solenoid overcurrent
M0710 Hydraulic fluid temperature too high M2102 Glow plug output error ON
M0711 Hydraulic fluid temperature extremely high M2103 Glow plug output error OFF
M0715 Hydraulic fluid temperature in shutdown M2107 Glow plug output open circuit
M0721 Hydraulic fluid temperature out of range high M2128 Glow plug output failure
M0722 Hydraulic fluid temperature out of range low M2202 Starter output error ON
M0810 Engine coolant temperature too high M2203 Starter output error OFF
M0811 Engine coolant temperature extremely high M2207 Starter output open circuit
M0815 Engine coolant temperature in shutdown M2228 Starter output failure
M0821 Engine coolant temperature out of range high M2302 Starter relay error ON
To Next Page
Loading...