BONANZA A-36 User Manual

Bonanza A-36
Specification:
Length :1632 mm(64.3")
Wing Span :2045 mm(80.5")
Wing Area :60.0 sq. dm
6.46 sq. ft
Wing Loading :106.7 g/sq. dm
34.9 oz/sq. ft
Flying Weight :6.4 kg(14.1 lbs)
Radio :6ch&9 servos
Engine :108 2-cycle
120 4-cycle
SAFETY PRECAUTIONS
INSTRUCTION MANUAL
First-time builders should seek advice from people having building
experience.If misused or abused,it can cause serious bodily injury
and damage to property.
Fly only in open areas and preferably at a dedicated R/C flying site.
We suggest having a qualified instructor carefully inspect your
airplane before its first flight.Please carefully read and follow all
instructions included with this airplane,your radio control system
and any other components purchased separately.
(The people under 18 years old is forbidden from flying this model)
This R/C airplane is not a toy!
132mm
Top view
Side View
20mm
20mm
RUDDER
3-way
pressure inlet
Air tank
3-way
pressure inlet
3-way
pressure inlet
3-way
pressure inlet
3-way
pressure inlet
Switch
Air inlet
Strut
Strut
Strut
Quick release connector
Make sure to assemble retracts as instructed below.
Three wheel retract system
Quick release connector
Pressure reduction inlet
Ø1.7mm
Ø0.2mm
The status when the
gear up
Pull out length of 8mm
to make gear down
Air valve
Air valve
3-way pressure inlet
5
1
Air tank
1
Air inlet
2
1
1
Air line (3000mm)
2
Quick release connector
Strut
( 90 )
1
Strut ( 110 )
Switch
Clevis
Rod (2X300mm)
1
1
1
Retainer
TP Screw(2.6x14mm)
2
Top view
Position for
right diagram.
ELEVATOR
Side View
30mm
30mm
Top view
25mm
25mm
35mm
AILERON
FLAP
Side View
FLAP
AILERON
Pleas notice the inner diameter for each
side of the pressure reduction inlet.
Please insure the sealing of the retract
system before flight .
Centre of Gravity.
Adjustment.
Adjustment.
Adjustment.
14
71
70
73
72

BONANZA A-36 Specifications

General

Manufacturer	Beechcraft
Type	Light aircraft
Horsepower	300 hp
Wingspan	33 ft 6 in (10.21 m)
Length	27 ft 6 in (8.38 m)
Crew	1
Capacity	5 passengers
Model	A-36
Max Takeoff Weight	3, 600 lb
Cruise Speed	176 knots (203 mph, 326 km/h)
Service Ceiling	18, 500 ft (5, 600 m)
Power	300 hp
Powerplant	Piston engine

Summary

Control Surface Adjustments

Aileron and Flap Travel Adjustment

Adjust the travel of each control surface to the values in the diagrams for general flight capabilities.

Elevator Travel Adjustment

Adjust the travel of each control surface to the values in the diagrams for general flight capabilities.

Rudder Travel Adjustment

Adjust the travel of each control surface to the values in the diagrams for general flight capabilities.

Centre of Gravity (CG) Check

Model Balancing Procedure

Never fly before checking the CG's required position and ensuring the model is well balancing.

Safety Precautions

Installation Steps

Install Nose Gear Wheel

Install the wheel to the nose gear as shown in the diagram.

Install Landing Gear Wheel and Door

Install the wheel and gear door to the landing gear.

Epoxy Nose Landing Gear

Epoxy the fixed nose landing gear to the fuselage.

Epoxy Main Landing Gear

Epoxy the fixed landing gear to the main wing.

Cowling and Engine Mount Assembly

Cowling Assembly

Assemble the cowling, ensuring proper fit with fuselage and mounting screws.

Canopy Gluing

Epoxy the canopy to the fuselage.

Wing and Control Surface Installation

Aileron to Main Wing Attachment

Assemble the aileron to the main wing with instant CA glue, ensuring free movement.

Wing and Flap Installation

Flap to Main Wing Attachment

Assemble the flap to the main wing with instant CA glue, ensuring free movement.

Control Linkage Setup

Servo Installation and Linkage

Secure the servo and install the nylon control horn, connecting the linkage.

Flap Servo and Linkage

Secure the flap servo and install the nylon control horn, connecting the linkage.

Elevator Servo and Pushrod

Install the elevator servo, ensuring the pushrod is secured.

Rudder Servo Installation

Install the servo for the rudder.

Receiver and Battery Mounting

Main Wing and Fuselage Integration

Main Wing Gluing

Epoxy the main wing together securely.

Main Wing to Fuselage Mounting

Accelerator Push Rod to Engine

Fuselage Servo and Switch Mounting

Fuel Tank Installation in Fuselage