What to do if BorMann Welding System flames out after running?
If your BorMann Welding System flames out after running for a while, ensure the ventilation knob on the fuel tank cap is in the ''ON'' position. Also, check both the fuel and oil levels, and add more if necessary.
How to fix a BorMann Welding System with spark plug splashed by fuel?
If the spark plug in your BorMann Welding System is splashed by fuel, remove the spark plug and wipe the fuel off.
What to do if BorMann Welding System has battery undercharge (electric start)?
If your BorMann Welding System has a battery undercharge (electric start), charge the battery by manually starting the generator for at least 30 minutes. After manually closing the choke, start the generator according to the manual start-up steps.
What if my BorMann Welding System has no ignition?
If your BorMann Welding System has no ignition, remove the spark plug cap and clean any dirt around the plug base, then remove the spark plug. Install the spark plug in the plug cap. Turn the combination switch to ''RUN'' position. Grounding the electrode to any engine ground, pull the recoil starter to see if sparks jump across the gap. If there is no spark, replace the plug. Reinstall the plug and start engine according to instructions.
Why BorMann Welding System lacks engine oil?
If your BorMann Welding System lacks engine oil, check the oil level. The engine is equipped with a low oil sensor and cannot be started unless the oil level is above the prescribed lower limit.
Why my BorMann Welding System generating set fails to start?
There are several reasons why your BorMann Welding System's generating set might fail to start: * The combination switch may be in the ''OFF'' or ''STOP'' position. If the engine is cold, turn the switch to ''CHOKE'' and follow the starting procedure. If the engine is hot, turn the switch to ''RUN'' and follow the starting procedure. * There may be a lack of fuel. Refill the fuel tank according to the manual's instructions. * There might not be enough engine oil. Check the oil level, as the engine has a low oil sensor that prevents starting if the level is too low. * There could be no ignition. Remove the spark plug cap, clean any dirt around the plug base, and remove the spark plug. Install the spark plug in the plug cap. Turn the combination switch to ''RUN'' position. Ground th...
Safety rules, hazard symbols (DANGER, WARNING, CAUTION), and essential safety messages for operation.
Warnings about hot surfaces, fire, moving parts, and electric shock risks.
Details on technical specifications and identification of main generator parts and controls.
Explains the function of power, overload, running, and oil alarm indicators.
Description of reset button, energy-saving switch, grounding, combination switch, circuit breaker, and parallel kit terminal.
Checklist for operation, location setup, and safety regarding toxic fumes and altitude.
Procedures for checking and adding engine oil and managing fuel levels and safety.
Steps for grounding, connecting the battery, and manually starting the generator.
Procedures for electric start, wireless remote control operation, and transmitter pairing.
Guidelines for connecting devices, calculating power needs, and avoiding overload.
Instructions for safely shutting down the generator and connecting multiple units in parallel.
Overview of scheduled maintenance for engine oil, filters, spark plugs, and other components.
Procedures for cleaning the exterior of the generator and adding engine oil.
Detailed steps for changing the oil, cleaning the air filter, and servicing the spark plug.
Addresses common starting problems, no output issues, and spark arrestor maintenance.
Procedures for storing the generator for long periods and for safe transportation.
Lists conditions and limitations under which the warranty is void or not applicable.
General| Welding Type | MIG/MAG |
|---|---|
| Input Voltage | 230 V |
| Frequency | 50/60 Hz |
| Welding Current Range | 30-200 A |
| Duty Cycle | 60% at 200 A |
| Wire Diameter | 0.6-1.0 mm |
| Protection Class | IP21S |
| Insulation Class | H |
| Output Current Range | 30-200 A |
| Weight | 15 kg |
| Electrode Diameter | 1.6-3.2 mm |
To Next Page
