Bosch BUTCHERS & BICYCLES MK1-E eBIKE SYSTEM Generation 3 - Operation

Page 47
English – 3
Fitting
Fitting and removing the on-board computer
(see figureA)
Fit the lower part of the Kiox into the holder(5) first and tilt
it forward gently until you can feel that the on-board com-
puter is firmly fixed in the magnetic holder.
To remove the on-board computer, hold it by the top end
and pull it towards you until it disengages from the magnetic
holder.
u Remove the on-board computer when you park the
eBike.
The on-board computer can be secured in place to prevent it
from being removed from the holder. To do this, loosen the
headset screw(16) until the Kiox holder can be swivelled
sideways. Put the on-board computer in the holder. Screw
the locking screw (M3 thread, 6mm long) from below into
the thread provided in the on-board computer (using a
longer screw may damage the on-board computer). Swivel
the holder back into place and tighten the headset screw in
accordance with the manufacturer's specifications.
Operation
Before initial commissioning
The Kiox is supplied with a partially charged battery. Before
using it for the first time, this battery must be charged for at
least one hour via the USB port (see "Power supply of the on-
board computer", pageEnglish – 3) or via the eBike sys-
tem.
The control unit should be attached such that the buttons
are almost perpendicular to the handlebars.
When using the on-board computer for the first time, the lan-
guage selection page is displayed initially. You can then
choose to have essential functions and indications explained
via the <Intro to Kiox> menu item. The menu item can also
be called up at a later time via <Settings>→ <Informa-
tion>.
Switching the on-board computer on/off
To switch on and switch off the on-board computer, briefly
press the on/off button(4).
Selecting system settings
Fit the on-board computer in the holder and proceed as fol-
lows with the bicycle stationary:
Go to the status page (use the <button(10) on the control
unit to get to the first display) and call up the <Settings>
with the select button.
You can use the –(11) and +(12) buttons to select the set-
ting you want. You can open the settings, as well as any addi-
tional submenus, using the select button(9). You can use
the <button(10) to go back to the previous menu from any
settings menu.
The following settings can be changed in the <Sys set-
tings>:
– <Brightness>
– <Time>
– <Date [DD.Mon.YYYY]>
– <Time zone>
– <24h form (24h time format)>
– <Brgh backg. (Bright background)>
– <Imp. units (Imperial units)>
– <Language>
– <Factory reset>
Starting up the eBike system
Requirements
The eBike system can only be activated when the following
requirements are met:
– A sufficiently charged eBike battery is inserted (see oper-
ating instructions for the battery).
– The on-board computer is properly fitted to the holder.
Switching the eBike system on/off
The following options are available for switching on the
eBike system:
– Once the on-board computer and the eBike battery are
fitted, briefly press the on/off button(4) on the on-board
computer.
– With the on-board computer inserted, push the on/off
button on the eBike battery (bicycle manufacturer-spe-
cific solutions are possible when there is no access to the
battery on/off button; see the battery operating instruc-
tions).
The drive is activated as soon as you start pedalling (except
if you are using the push-assistance function or if the assist-
ance level is set to OFF). The motor output depends on the
settings of the assistance level on the on-board computer.
As soon as you stop pedalling when in normal operation, or
as soon as you have reached a speed of 25/45km/h, the
eBike drive switches off the assistance. The drive is automat-
ically reactivated as soon you start pedalling again and the
speed is below 25/45km/h.
The following options are available for switching off the
eBike system:
– Briefly press the on/off button (4) of the on-board com-
puter.
– Switch off the eBike battery using its on/off button (bi-
cycle manufacturer-specific solutions are possible when
there is no access to the battery on/off button; see the bi-
cycle manufacturer operating instructions).
– Remove the on-board computer from its holder.
If no power is drawn from the eBike drive for about
10minutes (e.g. because the eBike is not moving) and no
button is pressed on the on-board computer or the operating
unit of the eBike, the eBike system, and therefore also the
battery, will switch off automatically to save energy.
Power supply of the on-board computer
If the on-board computer is in the holder(5), a sufficiently
charged eBike battery is inserted into the eBike and the
Bosch eBike Systems 1 270 020 XBK | (19.03.2021)