Bosch DWB67JP50 - Basic Operation

Basic operation en
7
6.6 Switching on the fan run-on
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
▶
Press ⁠
a The fan run-on starts at fan setting1.
a The appliance switches off automatically after ap-
prox. 10 minutes.
6.7 Switching off the fan run-on
▶
Press ⁠
6.8 Switching on automatic mode
1
The optimum fan setting is set automatically using a
sensor.
▶
Press ⁠.
6.9 Switching off automatic mode
1
▶
Press ⁠, ⁠or ⁠.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
6.10 Sensor control
1
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on. If the
sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡ Factory setting:3
¡ Lowest setting:1
¡ Highest setting:5
6.11 Setting the sensor control
Requirement:The appliance is switched off.
1.
Press and hold ⁠.
a The setting is displayed after approx. onesecond.
2.
Press ⁠, ⁠, ⁠, ⁠ or ⁠ to change the setting.
3.
Release ⁠ to save the setting.
6.12 Resetting the saturation
indicator_variant 1
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off, ⁠ and 1
appears on the display for the grease filter.
¡ After the appliance has been switched off, ⁠ and 2
appears on the display for the odour filter.
▶
Press ⁠.
a The saturation indicator is reset.
6.13 Resetting the saturation
indicator_variant 2
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off, ⁠ and 1
appears on the display for the grease filter.
¡ After the appliance has been switched off, ⁠ and 1
appears on the display for the odour filter.
1.
To reset the saturation indicator for the grease filter,
press ⁠.
2.
To reset the saturation indicator for the odour filter,
press ⁠.
a The saturation indicator is reset.
6.14 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement:The appliance is switched off.
1.
Press and hold ⁠.
‒ To set circulating-air mode (non-regenerative fil-
ter), press ⁠.
‒ To set circulating-air mode (regenerative filter),
press ⁠.
‒ To set air extraction mode, press ⁠.
2.
Release ⁠ to save the setting.
6.15 Switching on the lighting
The lighting can be switched on and off independently
of the ventilation system.
▶
Press ⁠.
6.16 Setting the brightness
▶
Press and hold ⁠ until the required brightness is
reached.
6.17 Switching on the audible signal
Requirement:The appliance is switched off.
▶
Press and hold ⁠ and ⁠ at the same time for ap-
prox. threeseconds until a signal sounds.
6.18 Switching off the signal tone
Requirement:The appliance is switched off.
▶
Press and hold ⁠ and ⁠ at the same time for ap-
prox. 3 seconds.
a A signal tone will sound.
1
Depending on the appliance specifications