Bosch FLEXIDOME IP starlight6000 VR NIN-63013

Questions and Answers

K
Keith JacksonAug 4, 2025
Why Bosch Dome camera has no connection and image transmission?
- D
  dannyjonesAug 4, 2025
  If your Bosch Dome camera isn't establishing a connection or transmitting images, there might be several reasons. First, the unit configuration could be incorrect, so check all configuration parameters, and if needed, reset to factory default. Second, faulty installation may be the cause, so check all cables, plugs, contacts, and connections. Third, the IP address might be wrong, so verify the IP addresses by using the ping command. Also, faulty data transmission within the LAN could be the reason, so check the data transmission with ping. Finally, the maximum number of connections might have been reached; in this case, wait until a connection is free and try connecting again.
A
Adrienne PerkinsAug 9, 2025
What to do if my Bosch Dome camera does not operate?
- M
  melanie52Aug 9, 2025
  If your Bosch Dome camera isn't operating, it could be due to a power failure. In this case, check the power supply. Alternatively, there might be faulty cable connections. To resolve this, check all cables, plugs, contacts, and connections.
C
Christopher PhillipsAug 14, 2025
What to do if my Bosch Dome camera is not operational after a firmware upload?
- D
  Daniel RobersonAug 14, 2025
  If your Bosch Dome camera is not operational after a firmware upload, it could be due to a power failure during programming by firmware file. In this case, have the unit checked by Customer Service and replace if necessary. Another reason could be an incorrect firmware file. To resolve this, enter the IP address of the unit followed by /main.htm in your Web browser and repeat the upload.
T
Tamara FitzgeraldAug 19, 2025
Why is there no audio transmission to remote station on my Bosch Dome camera?
- B
  Brent DanielsAug 19, 2025
  If you're experiencing no audio transmission to the remote station with your Bosch Dome camera, it could be due to a hardware fault. Check that all connected audio units are operating correctly. Another cause might be faulty cable connections, so check all cables, plugs, contacts, and connections. Additionally, incorrect configuration could be the issue; check audio parameters on the Audio configuration and LIVE page functions pages. The audio voice connection might also be in use by another receiver, so wait until the connection is free and then call the sender again.
G
Gregory CarrAug 25, 2025
Why Bosch Dome camera web browser contains empty fields?
- Z
  Zachary KelleyAug 25, 2025
  If your Bosch Dome camera web browser contains empty fields, it might be due to an active proxy server in the network. To solve this, create a rule in the local computer's proxy settings to exclude local IP addresses.
A
Arthur BaileyAug 29, 2025
What to do if my Bosch Dome camera does not report an alarm?
- T
  Tyler GomezAug 29, 2025
  If your Bosch Dome camera isn't reporting an alarm, it might be because the alarm source is not selected. To fix this, select possible alarm sources on the Alarm sources configuration page. Alternatively, no alarm response might be specified. Specify the desired alarm response on the Alarm connections configuration page; if necessary change the IP address.

Summary

Safety

Safety Precautions

General safety instructions and precautions for installation and operation.

Short Information

System Overview

Performance

Details on camera image quality, resolution, frame rate, and housing.

Using the Camera

Instructions for accessing camera features via web browser and software applications.

Application Variants

Explanation of different camera modes for optimal performance in specific environments.

Planning Information

Unpacking

Guidance on how to unpack the equipment and verify contents.

List of items included in the camera packaging and surface mount box.

Installation

Preparation

Steps to separate camera parts and prepare for installation.

Local Storage

Information on using memory cards for alarm recording and data backup.

Wiring

Details on connecting flying leads, watertight compartments, and surge suppression.

Cable Tree

Table identifying wire colors, AWG, and signal types.

Earthing

Instructions for connecting the device to earth for safety and EMC/RFI protection.

Network (and PoE power)

Connecting the camera to a network via STP Cat5e cable and Power-over-Ethernet.

Auxiliary Power

Connecting a 12 VDC power supply as an auxiliary source.

Alarm

Connecting alarm input/output devices and their specifications.

Audio

Connecting audio devices for full-duplex mono audio communication.

Video

Connecting an analog monitor via CVBS for setup or output.

Mounting the Camera Module

Procedures for mounting the camera module to the ceiling.

Mounting Flush to Ceiling

Detailed steps for flush mounting the camera module into a ceiling.

Mounting to Ceiling with SMB-IP

Instructions for mounting the camera using a Surface Mount Box (SMB-IP).

Camera Positioning and Field-of-View

Adjusting the camera module's position and field-of-view.

Pan

Instructions for adjusting the camera's horizontal pan.

Tilt

Instructions for adjusting the camera's vertical tilt.

Twist

Adjusting the camera module's twist for a horizontal horizon.

Local Set-up

Using the control panel's Menu button for initial camera setup via the install wizard.

Using the Install Wizard

Step-by-step guide to using the camera's install wizard for setup.

Reset

How to use the factory reset button to restore default settings.

Mount Inner and Outer Dome

Steps to attach the inner and outer domes after positioning.

Connection via Web Browser

Configuration

Troubleshooting

Resolving Problems

Table of malfunctions, possible causes, and solutions for troubleshooting.

Testing the Network Connection

How to use the ping command to check network connectivity.

Customer Service

Contact information and procedure for seeking assistance from customer service.

Maintenance

Cleaning

General guidelines for cleaning the camera unit.

Lens Cleaning

Specific instructions for cleaning the camera lens to ensure optimal performance.

Repair

Information regarding unit repair and limitations on user serviceability.

Decommissioning

Transfer

Guidance on passing the unit on, including the installation guide.

Disposal

Instructions for environmentally compatible disposal of the electronic unit.

Technical Data