8 | English
1 609 92A 01D | (11.2.13) Bosch Power Tools
Additional safety warnings
Do not reach into the saw dust ejector with your hands.
They could be injured by rotating parts.
Do not work overhead with the saw. In this manner you
do not have sufficient control over the power tool.
Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility
company for assistance. Contact with electric lines can
lead to fire and electric shock. Damaging a gas line can
lead to explosion. Penetrating a water line causes proper-
ty damage.
Do not operate the power tool stationary. It is not de-
signed for operation with a saw table.
Do not use high speed steel (HSS) saw blades. Such saw
blades can easily break.
Do not saw ferrous metals. Red hot chips can ignite the
dust extraction.
When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e.g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Ventilate the area and seek
medical help in case of complaints. The vapours can irri-
tate the respiratory system.
Use the battery only in conjunction with your Bosch
power tool. This measure alone protects the battery
against dangerous overload.
Use only original Bosch batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e.g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for lengthways and crossways cut-
ting of wood with straight cutting lines as well as mitre cuts in
wood while resting firmly on the workpiece.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Lock-off button for On/Off switch
2 On/Off switch
3 Battery pack*
4 Blade guard
5 Lever for retracting blade guard
6 Base plate
7 Retracting blade guard
8 Parallel guide
9 Cutting mark, 0°
10 Cutting mark, 45°
11 Wing bolt for bevel-angle preselection
12 Wing bolt for parallel guide
13 Scale for mitre angle
14 Spindle lock button
15 Auxiliary handle (insulated gripping surface)
16 Allen key
17 Handle (insulated gripping surface)
18 Saw spindle
19 Mounting flange
20 Saw blade*
21 Clamping flange
22 Clamping bolt with washer
23 Marks on the blade guard
24 Battery unlocking button
25 Fastening screw for extraction adapter
26 Extraction adapter
27 Vacuum hose*
28 Cutting-depth scale
29 Clamping lever for cutting-depth preselection
30 Set of screw clamps*
31 Button for charge-control indicator*
32 Battery charge-control indicator*
33 Guide rail*
34 Connection piece*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Circular Saw GKS 18 V-LI
Article number
3 601 F6H 0..
Rated voltage
V= 18
No-load speed
min
-1
3900
Cutting depth, max.
–for 0° bevel angle
– for 45° bevel angle
mm
mm
51
40
Spindle lock
* dependent of the battery pack being used
OBJ_BUCH-765-002.book Page 8 Monday, February 11, 2013 11:29 AM
To Next Page
Loading...
