12 | English
1 609 92A 4A9 | (13.06.2018) Bosch Power Tools
Application tool Material Application
Bi-metal plunge cut
saw blade for wood
and metal
Softwood, hardwood,
veneered boards, plastic-
coated boards, non-
hardened nails and
screws
Fast, deep plunge cuts in wood and metal;
example: Fast cutting of wood containing nails, deep
plunge cuts in laminated boards and precise shortening of
door frames
Bi-metal plunge cut
saw blade for wood
and metal
Wood, abrasive wood-
based materials, plastics,
hardened nails and
screws, non-ferrous metal
pipes
Fast, deep plunge cuts in wood, abrasive wood-based ma-
terials and plastics;
example: Fast cutting of non-ferrous metal pipes and pro-
files with small dimensions, easy cutting of non-hardened
nails, screws and steel profiles with small dimensions
TC plunge cut saw
blade, metal
Stainless steel, screws
and nails, epoxy resin,
fibreglass-reinforced
plastics, fibreglass, plas-
terboard, porous concrete
Fast, deep plunge cuts in severely abrasive materials or
metal;
example: Fast cutting of kitchen front covers, easy cutting
through hardened screws, nails and stainless steel.
HCS plunge cut
saw blade for wood
Softwood, dowels, pins,
furniture elements
Fast, deep separating cuts and plunge cuts;
including sawing close to edges in corners and in difficult-
to-reach areas;
example: Deep plunge cut in softwood for installing a vent-
ilation grille
Fitting/changing the application tool (GOP30‑28)
Remove the application tool if one has already been fitted.
To remove the application tool, use the hex key (7) to loosen
the clamping bolt(6) and remove the tool.
Position the required application tool (e.g. plunge cut saw
blade (5)) on the tool holder (4) so that the depressed
centre is facing downwards (see figure on the graphics page,
text on the application tool should be legible from above).
Turn the application tool to a position which is convenient
for the job at hand and allow it to lock into place in the cams
of the tool holder (4). Twelve positions offset by 30° are
possible for this.
Secure the application tool using the bolt(6). Tighten the
bolt using the hex key(7) until the rounded head of the bolt
is lying flat against the application tool.
u Check that the application tool is seated securely. Ap-
plication tools that are attached incorrectly or are not se-
curely fixed in place may come loose during operation,
thereby putting you at risk.
Fitting/changing the application tool (GOP40‑30/
GOP55‑36)
Remove the application tool if one has already been fitted.
To do so, open the SDS lever (12) all the way. The applica-
tion tool/accessory will be ejected.
Position the required application tool (e.g. plunge cut saw
blade (5)) on the tool holder (4) so that the depressed
centre is facing downwards (see figure on the graphics page,
text on the application tool should be legible from above).
When doing so, place the application tool/accessory in a po-
sition which is convenient for the job at hand. Twelve posi-
tions offset by 30° are possible for this.
Press the application tool in the required position firmly onto
the clamping jaws of the tool holder until it locks automatic-
ally.
u Check that the application tool is seated securely. Ap-
plication tools that are attached incorrectly or are not se-
curely fixed in place may come loose during operation,
thereby putting you at risk.
Mounting and adjusting the depth stop
The depth stop(15) can be used when working with seg-
ment and plunge cut saw blades.
Remove the application tool if one has already been fitted.
Slide the depth stop(15) into the required working position
over the tool holder(4) and onto the collar of the power tool
as far as it will go. Allow the depth stop to engage. Twelve
positions offset by 30° are possible for this.
Set the depth you wish to work at. Push the clamping lever
(14) of the depth stop shut to fix the depth stop in position.
Selecting a sanding sheet
Different sanding sheets are available, depending on the material you are working with and the required surface removal rate:
To Next Page
Loading...
