14 | English
1 609 92A 0WG | (16.10.15) Bosch Power Tools
Technical Data
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted sound pressure level of the product
is 76 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60745-2-4:
a
h
=7.5m/s
2
, K=1.5 m/s
2
.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-4.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 13.10.2015
Assembly
Before any work on the machine (e. g. maintenance,
changing the tool, etc.) as well as during its transport
and storage, lock the On/Off switch in the off position.
There is danger of injury when the On/Off switch is unin-
tentionally actuated.
Battery Charging
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Orbital sander GSS 18V-10
Article number
3 601 JD0 2..
Rated voltage
V= 18
No-load speed
min
-1
11000
No-load orbital stroke rate
min
-1
22000
Sanding sheet surface
cm
2
114.7
Orbit diameter
mm 1.6
Dimensions
mm 199.5 x 113 x 141
Weight according to EPTA-Procedure 01:2014
kg 1.4/1.7*
Permitted ambient temperature
– during charging
– during operation
**
and during storage
°C
°C
0...+45
–20...+50
Recommended batteries
GBA 18V..
GBA 18V... W
Recommended chargers
AL18..
GAL 3680
GAL 18... W
*depending on the battery pack being used
** Limited performance at temperatures <0 °C
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-2269-001.book Page 14 Friday, October 16, 2015 10:44 AM
To Next Page
Loading...
