Bosch SHX3AR75UC Use And Care Manual

13
Operating the Dishwasher
Start the dishwasher:
1 Open the door and press the On/Off button.
2 One of the wash cycle LEDs will be flashing. You can now select a wash cycle.
3 Press the Cycle Select arrow buttons to select the desired wash cycle.
4 Press Start and close the door to begin the cycle.
Cancel a cycle:
1 Open the dishwasher door just far enough to expose the control panel. Be careful of hot water that
may splash out.
2 Press and hold Start until the “Active” LED goes out.
3 Close the door and wait about 1 minute until the unit beeps, indicating it is done draining.
4 Open the door and press the On/Off button. You may now start a new cycle.
WARNING
You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR
CAREFULLY during any wash or rinse cycle. Do not fully open the door until water noises have stopped.
To enter options mode:
1 With the door open, press the On/Off button to turn the unit on.
2 One of the wash cycle LEDs will be flashing.
3 Press and hold down the > button, then press and release the Start button. Now release the > button.
4 The “Clean” LED and one other LED will be flashing. You are now in options mode.
5 Press the > button to select the option you would like to adjust.
To set amount of Rinse Aid:
Note: If your glasses have spots on them, you need more rinse aid. If your glasses have streaks on them, you
need less rinse aid.
1 Follow the prior instructions to enter options mode.
2 With the “Clean” and “Refill Rinse Aid” LEDs flashing, press the < button to change the amount of
rinse aid dispensed.
0 LEDs flashing = rinse aid is OFF
1 LED flashing = lowest amount of rinse aid dispensed
2 LEDs flashing = medium amount of rinse aid dispensed
3 LEDs flashing = highest amount of rinse aid dispensed
3 Press Start to save your setting.
To turn Extra Dry Heat ON or OFF:
1 Follow the prior instructions to enter options mode.
2 With the “Clean” and “Sanitized” LEDs flashing, press the < button to turn Extra Dry Heat ON or OFF.
0 LEDs flashing = Extra Dry Heat is OFF
1 LED flashing = Extra Dry Heat is ON
3 Press Start to save your setting.
To set the Cycle Completion Signal:
1 With the “Clean”, “Sanitized” and “Refill Rinse Aid” LEDs flashing, press the < button to change the
cycle completion tone volume. The wash cycle LEDs will illuminate when you press <.
0 LEDs flashing = Cycle Completion Signal is OFF
1 LED flashing = low tone volume
2 LEDs flashing = medium tone volume
3 LEDs flashing = highest tone volume
2 Press Start to save your setting.

Bosch SHX3AR75UC Specifications

General

Door color	Stainless steel
Control type	Buttons
Tub material	Plastic
Certification	CSA, UL
Built-in display	No
Control panel type	English
Outlet hose length	2.3 m
Appliance placement	-
Upper basket adjustable height	Yes
Current	12 A
Connected load	1400 W
AC input voltage	120 V
AC input frequency	60 Hz
Power consumption (off)	- W
Water consumption per cycle	- L
Energy consumption per cycle	- kWh
Cycle time	30 min
Noise level	50 dB
Delay start (max)	9 h
Number of place settings	14 place settings
Number of washing programs	6
Net weight	32200 g
Gross weight	35800 g
Dimensions (WxDxH)	860.4 x 598.5 x 603 mm
Annual water consumption	688 L
Annual energy consumption	269 kWh
Installation compartment dimensions (WxDxH)	890 x 600 x 610 mm
Sustainability certificates	ENERGY STAR
Package depth	682.6 mm
Package width	911.2 mm
Package height	660 mm

Weight and Dimensions

Depth	6032.5 mm
Width	598.487 mm
Height	860.425 mm
Weight	32205 g
Installation compartment depth	600 mm
Installation compartment width	890 mm
Installation compartment height	610 mm