Need help?Do you have a question about the Bosch SMV2ITX18G and is the answer not in the manual?
General| Door color | White |
|---|---|
| Cord length | 175 m |
| Control type | Buttons |
| Product size | Full size (60 cm) |
| Tub material | Stainless steel |
| Built-in display | - |
| Inlet hose length | 165 m |
| Custom panel-ready | No |
| Outlet hose length | 190 m |
| Appliance placement | Fully built-in |
| Control panel color | Black |
| Current | 10 A |
| Connected load | 2400 W |
| AC input voltage | 220/240 V |
| AC input frequency | 50 - 60 Hz |
| Energy efficiency scale | A to G |
| Power consumption (off) | 0.5 W |
| Water consumption per cycle | 10.5 L |
| Energy consumption per cycle | 0.923 kWh |
| Cycle time | 270 min |
| Noise level | 48 dB |
| AquaSensor function | Yes |
| Dishwashing programs | Auto 45-65°C, Eco 50°C, Express, Favorite, Intensive 70°C, Pre-rinse |
| Number of place settings | 12 place settings |
| Number of washing programs | 5 |
| Package weight | 33200 g |
| Feet adjustment | 60 mm |
Weight and Dimensions| Depth | 550 mm |
|---|---|
| Width | 598 mm |
| Height | 815 mm |
| Weight | 31100 g |
| Depth with door open | 1150 mm |
| Installation compartment width | 600 mm |
| Installation compartment height | 875 mm |
Improper installation is dangerous. Connect to properly installed earthed socket.
Follow detergent/rinse aid instructions. Avoid solvents, caustic agents.
Operating a damaged appliance or power cord is dangerous. Never operate damaged unit.
Prevent damage from escaping steam. Avoid corrosion from special salt. Use only dishwasher salt.
Connect to a suitable power supply (220-240V, 50/60Hz).
Steps for initial setup: adding salt, rinse aid, switching on, setting water hardness.
Determine and set the water hardness on the appliance.
How to fill the special salt dispenser and precautions.
Steps to fill the rinse aid dispenser.
How to adjust the amount of rinse aid dispensed for optimal results.
Explains suitability of tabs, powder, and liquid detergents.
Instructions on opening the detergent dispenser and adding detergent.
Detailed steps for adding detergent or tablets to the dispenser.
How to switch on the appliance; default Eco 50° programme.
How to select a programme using the programme button.
How to start, interrupt, and resume programmes.
How to cancel a programme early.
How to switch the appliance off using the power button.
Configure water hardness level.
Adjust rinse aid dispensing or switch off.
Connect appliance to mobile device for control via Home Connect app.
Start appliance remotely via app. Requirements and activation.
Instructions for cleaning the micro, fine, and coarse filters.
Steps to remove, clean, and re-install spray arms to ensure proper function.
List of faults, causes, and troubleshooting steps for error codes and signal lights.
Troubleshooting for kinked hoses, turned-off taps, and blocked filters.
Troubleshooting for water supply errors, flashing displays, and door not closed.
Causes and solutions for tableware not drying properly.
Solutions for poor drying, plastic items, and cutlery not drying.
Causes and solutions for a wet interior and food remnants on tableware.
Troubleshooting for blocked spray arms, soiled filters, and incorrect filter insertion.
Solutions for weak programmes, over-pre-cleaning, and inadequate rinsing of corners.
Causes and solutions for detergent residue blocking the dispenser.
Troubleshooting for water marks on plastic and coatings inside the appliance.
Causes and solutions for stubborn white coatings from detergent or hardness.
Troubleshooting for tea marks and coloured films from vegetables or tap water.
Solutions for coloured deposits, discolouration, and streaks on glassware.
Troubleshooting for detergent residue and blocked dispenser lids.
Solutions for irreversible clouding of glassware and rust spots on cutlery.
Causes and solutions for excessive foam formation.
Troubleshooting for excessive foam and detergent brand impact.
To Next Page
