To Next PageTo Next Page
Need help?Do you have a question about the Bosch Universal Aquatak 130 and is the answer not in the manual?
General| Pressure | 130 bar |
|---|---|
| Flow Rate | 380 L/h |
| Hose Length | 6 m |
| Weight | 7.8 kg |
| Max Water Temperature | 40°C |
| Cable Length | 5 m |
| Frequency | 50 Hz |
| Included Accessories | High-pressure gun, Lance, High-pressure detergent nozzle, 6m high-pressure hose |
| Lance | Variable Fan Jet Nozzle |
General hazard safety alert. Never direct water jet at people, animals, unit, or electric components. High pressure jets can be dangerous.
Read all warnings and instructions. Failure may cause electric shock, fire, or injury. Follow general safety regulations.
Ensure rating plate voltage matches power source. Use RCD, protect cords from damage, and avoid wet hands when handling plugs.
Comply with water supply regulations. Use reinforced hoses, sealed joints. Never use without a back flow valve.
High-pressure hose must not be damaged. Replace immediately. Use only manufacturer-recommended hoses and connections.
Check unit and equipment condition. Do not direct jet at people/animals. Avoid solvents. Place unit on a solid base.
Ensure adequate ventilation in confined spaces. Operate with both hands. Do not operate from a ladder or raised areas.
Use only manufacturer-recommended detergents. Observe dilution and warning instructions. Keep out of reach of children.
Wear protective clothing (goggles, etc.). Be aware of aerosols. Vehicle tyres need minimum distance. Do not spray asbestos materials.
Never use without a water filter or with a contaminated one. Avoid high-pressure washing in bad weather, especially during lightning risk.
Operator must be authorized and trained. Unit must not be operated by children or unauthorized persons.
Supervise children. Do not leave unsupervised when switched on. Hold gun firmly with both hands. Do not use roto/pencil jet on vehicles.
Switch off the motor and secure the unit before transporting.
Switch off unit before cleaning/maintenance. Pull mains plug. Repairs only by authorized Bosch Service Centres.
Use only Bosch-approved accessories and spare parts for safety and to prevent breakdowns.
Symbols are important for understanding instructions. Correct interpretation helps safer machine use.
For cleaning outdoor areas, objects, tools, vehicles, and boats. Not for professional use.
Technical data including article number, rated power, supply temperature, pressure, flow, and weight.
Lists items included in the delivery scope and references figures for assembly and operation.
Machine is double insulated. Use RCD. Inspect supply cables for damage. Use only approved extension cables.
Extension cables must be watertight, for outdoor use, and meet specific standards (EN 61242/IEC 61242).
Attach water supply, connect to mains, open tap, release trigger safety, press trigger for constant flow, then press safety lock.
The machine is designed to switch off the motor when the trigger is released on the gun.
Ensure unit is on level ground. Do not overreach with hose. Do not kink hose. Never use roto/pencil jet on vehicles.
Select fan jet, apply detergent sparingly with foam bottle, rinse off loosened dirt and detergent.
Unit is self-priming. Use clean water filter. Immerse hose to displace air. Operate until water flows uniformly.
Check plug, socket, fuse, cable, protector. Allow to cool if frozen or protector activated.
Check fuse, voltage, protector. Allow to cool if protector activated or frozen.
Check for faulty fuses, incorrect rating, or wrong mains voltage.
Check nozzle, power, cable, water supply, filter, kinks, or hose length.
Air, inadequate supply, or worn valve. Run with open spray handle to obtain regular pressure.
Likely TSS (Total Stop System) device issues. Contact Bosch Service Centre for diagnosis.
Slight leaks are permissible. Excessive leaks may indicate pump issue, contact Service Centre.
Check detergent density or nozzle restriction. Dilute or flush nozzle.
Regularly check for defects, loose fixings, worn components, undamaged covers and guards.
If the supply cord is damaged, it must be replaced by Bosch or an authorized service agent to avoid hazards.
Drain water, clean exterior, remove debris, store in frost-free area. Ensure cables are not trapped.
Provides contact details for service centres in various regions for correspondence and spare parts orders.
