Boss Audio Systems 480BRGB User Manual

- Only support speakers of 4 ohms or above
- +12V DC Negative Ground.
- The maximum current of the Amp remote trigger is 200mA.
!
Wiring Connections
White
Front Left
Speaker
Rear Left
Speaker
Front Right
Speaker
Rear Right
Speaker
White/Black
ACC + (Red)
GND - (Black)
ANT + (Blue)
Power B+ (Yellow)
Gray/Black
Purple
Purple/Black
Green
Green/Black
Gray
Installation
Installation Procedures
First complete the electrical connections and then check for correctness of
connection.
Installation Opening
This unit can be installed in any dashboard
which has an opening as shown below.
To Install the Car Radio
Be sure you test all connections first, and then follow these steps to install
this unit.
1. Make sure the ignition is turned off, and then disconnect the cable from
the vehicle battery’s negative (-) terminal.
2. Disconnect the wire harness and the antenna.
3. Remove the plastic outer trim from the car receiver.
4. Attach the “L” brackets (2pcs) on the both sides of the car receiver with
screws(M5.5 x 7) as shown as the below figure. The others fixing screws that
fix the other terminal of the “L” metal bracket, please buy from your dealer
according to the drilling of holes size.
7.2 inches
4.1 inches
5. Consult with you nearest dealer if installation requires the drilling of holes
or other modifications of the vehicle.
6. Install this car receiver in the dashboard.
7. Make wiring connections, as illustrated in the “Wiring Connections.”
8. Install the plastic outer trim ring onto the car receiver.
10A
Adjust Menu Options
• Press and hold the volume knob to enter into setting menu, then press the
volume knob repeatedly to select setting items:
- BASS/TREBLE:-7, -6, ~, 1, 0, +1,~, +6, +7
Note: BASS and TREBLE settings are only enabled when EQ setting is
turned OFF.
- BALANCE:L7, L6,~, L1, 0, R1,~,R6, R7
- FADER:R7, R6, ~, R1, 0, F1, ~ ,F6, F7
- EQ(Equalizer) Setting: OFF, FLAT, CLASSIC, POP, ROCK, JAZZ
- Loudness: LOUD ON/OFF
- DX/LOCAL: Enables or disables the local broadcast mode (LOCAL).
- Stereo/Mono: Switches between MONO and STEREO reception mode
for radio frequencies.
- CLOCK 12/24: Select between 12 hours and 24 hours display.
Note: If 12 hour display is selected , AM= Morning; PM= Afternoon
- AREA US/EU: This car radio is equipped the USA / Europe frequency.
Rotate the volume knob to switch between USA and Europe frequency.
The system will change the frequency setting in about 3 seconds.
- 7 color-changing illumination in buttons:
This car radio device is equipped 7 color-changing illumination in buttons.
The illumination color can be preset Auto(color automatically change one
by one), Blue, Red, Cyan, Green, Purple, Yellow, White.
• Rotate the volume knob to change values.
Mute On/Off
In power on mode, briefly press the MUTE button to toggle mute on or off.
Setting the Clock
Press the CLOCK button to display time. Press and hold the CLOCK button
again. The hours digits start flashing on the display.
Set hours by rotating the volume knob. Briefly press the CLOCK button.
The minute digits start flashing. Set minutes by rotating the volume knob.
USB Port
Connect to a USB storage device for audio play, or charging of a mobile
phone.
Hands-free Microphone
To receive your voice when calling by using this bluetooth handsfree system.
Aux Audio Input Jack
Connect to the headphone jack on an external device (e.g. a mobile phone
or MP3 player) for audio play.
Turn Unit on/off, Change the Source
• Press the /SRC button to turn on the unit. Press and hold the /SRC
button to turn off the unit.
• Press the /SRC button to select the different modes: Radio, USB(with
USB device inserted), AUX-IN(aux audio input) and BT(Bluetooth).
Adjust the volume
Rotate the volume knob to increase or decrease the volume level.
Push-To-Talk
Press the button (volume knob) to access to smartphones voice
assistant capability via Bluetooth.
Overview of the Components
General Operation
General Operation General Operation
Radio Operation
Switch Between USA area and Europe area Frequency
In radio mode, press and hold the volume knob to enter into setting menu,
then press the volume knob repeatedly to access the state of the USA and
Europe frequency, then rotate the volume knob to switch between USA and
europe frequency. The system will change the frequency setting in about 3
seconds.
Change Bands
In radio mode, shortly press the BAND button to switch between the
FM1(F1), FM2(F2), FM3(F3) and AM1(A1), AM2(A2) bands.
To Store / Recall Preset Stations
The radio can be stored 6 preset stations for each band (FM1, FM2, FM3,
AM1 and AM2) for a total of 30 preset stations.
- To memorize a station:
Press and hold the desired preset buttons (1-6) to save a radio station.
- To recall a preset station:
Briefly press the respective station button (1-6) to recall the corresponding
preset station.
Manual Tuning
In the radio mode:
Press and hold the or button to enter the manual tuning mode.
In manual tuning mode, briefly press the or button to search the next
or previous frequency step by step.
Seek Tuning
In radio mode, press the or button, the automatic search will start, it
will search upward or downward for the strong signal radio station within the
current band. The auto searching will stop until find a station.
Automatic Store Preset station (AMS)
Press and hold the AMS button to store 18 FM stations and 12 AM stations
automatically.
Briefly press the AMS button to recall each preset station that saved in the
memories in each band.
(power) / SRC (source) button
VOL (volume) knob, (Push-To-Talk) button, SEL (select/menu) button
BAND button, (answer call) button
AMS (automatic store station, preset station scan, automatic music search) button
(pause/play), Preset station 1 button
RPT (repeat), Preset station 3 button
-10(previous 10 tracks), previous folder, Preset station 5 button
1.
2.
3.
5.
4.
INT (intro), Preset station 2 button6.
7.
RDM (random), Preset station 4 button8.
9.
10. +10(next 10 tracks), next folder, Preset station 6 button
11. CLOCK (clock display/setting), (end call) button
12. (tune/seek down, previous track, fast reverse) button
13. (tune/ seek up, next track, fast forward) button 14. MUTE button,
15. EQ (Equalizer), 16. IR remote sensor, 17. LCD Display, 18. USB Port,
19. AUX IN (aux audio input) jack 20. Hands-free Microphone 21. Reset button
Reset
Push the RESET button with a thin object with a pointed end to reset the unit.
This function may be used when the LCD does not display normally or sound
is distorted, or when any of controls are disabled.
1918
21
20

Boss Audio Systems 480BRGB Specifications

General

Brand	Boss Audio Systems
Model	480BRGB
Category	Car Video System
Language	English

Summary

Installation

Installation Procedures

First complete the electrical connections and then check for correctness of connection.

Installation Opening

This unit can be installed in any dashboard which has an opening as shown below.

To Install the Car Radio

Be sure you test all connections first, and then follow these steps to install this unit.

Wiring Connections

Overview of the Components

General Operation

Turn Unit on/off, Change the Source

Press the /SRC button to turn on the unit. Press and hold the /SRC button to turn off the unit.

Adjust the volume

Rotate the volume knob to increase or decrease the volume level.

Push-To-Talk

Press the button (volume knob) to access to smartphones voice assistant capability via Bluetooth.

Adjust Menu Options

Press and hold the volume knob to enter into setting menu, then press the volume knob repeatedly to select setting items.

Mute On/Off

In power on mode, briefly press the MUTE button to toggle mute on or off.

Setting the Clock

Press the CLOCK button to display time. Press and hold the CLOCK button again. The hours digits start flashing.

USB Port

Connect to a USB storage device for audio play, or charging of a mobile phone.

Hands-free Microphone

To receive your voice when calling by using this bluetooth handsfree system.

Aux Audio Input Jack

Connect to the headphone jack on an external device (e.g. a mobile phone or MP3 player) for audio play.

Reset

Push the RESET button with a thin object with a pointed end to reset the unit.

Radio Operation

Switch Between USA area and Europe area Frequency

In radio mode, press and hold the volume knob to enter into setting menu, then press the volume knob repeatedly to access the state of the USA and Europe frequency.

Change Bands

In radio mode, shortly press the BAND button to switch between the FM1, FM2, FM3 and AM1, AM2 bands.

To Store / Recall Preset Stations

The radio can be stored 6 preset stations for each band (FM1, FM2, FM3, AM1 and AM2).

Manual Tuning

Press and hold the or button to enter the manual tuning mode. Press the or button to search the next or previous frequency step.

Seek Tuning

Press the or button, the automatic search will start, it will search upward or downward for the strong signal radio station.

Automatic Store Preset station (AMS)

Press and hold the AMS button to store 18 FM stations and 12 AM stations automatically.

USB Operation

Select Next Track or Previous Track

In the USB mode, briefly press the or button to play the next or previous track.

Fast Forward/Reverse

Press and hold the or button to fast forward or reverse a track.

Play / Pause

Press the II button to interrupt the playback of a music (pause function).

Introduction Scan

Press the INT button to play the first 10 seconds of each track.

Repeating the track

Press the RPT button to toggle between RPT ONE, RPT FLR, and RPT ALL.

Playing all tracks in random

Press RDM once to play all tracks randomly. Press RDM once again to exit random playback.

Track/Folder Navigation

Press the -10/+10 buttons to jump 10 tracks backward or forward.

Select the track or file for playback in MP3 format

Press the AMS button to enter track search mode. Rotate volume knob to select track number.

Aux Audio Operation

Bluetooth Operation

Pair and Connect

Pair the mobile phone with the device before using it. Enable BT mode on your mobile phone.

Make a Call

Dial the call directly from the paired mobile phone or use the remote control to input number.

Answer a Call

When the mobile phone is called, the incoming telephone number displays on the LCD.

Reject or End a Call

To reject or end the call, press the button.

Redial Last Dialed Number

Press the button to redial the last dialed phone number.

Switch Audio Between Car Audio and mobile Phone

During a call, press the volume knob to switch the audio source from the car audio system back to your mobile phone.

Audio Streaming (A2DP)

The unit supports A2DP wireless streaming audio from your Bluetooth mobile device.

Push-To-Talk

Allows direct access to Android and IOS smartphones voice assistant capability when user establish the bluetooth connection.

Remote Control

Specifications

General

Details power supply, maximum output, speaker impedance, unit dimensions, weight, and fuse rating.

Radio

Details frequency range and channel step for FM reception.

AM

Details frequency range and channel step for AM reception.

USB

Lists usable audio formats, USB port type, charging capability, pre-amp output, and frequency response.

BT

Specifies supported BT profiles and frequency range.